Ariens Path-Pro 136E User Manual Page 18
- Page / 80
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
LlNKing
Files
Table
5
-
LlNKing
to
Another File.
The Series 920 enables you to link
files
together. The LINK step allows you to link the
last step of a profile to the first step of another profile.
Lets edit the program again by adding a LINK step at the end of the profile. But first,
lets create another file.
If you run your program with a LINK going to a
non-existing
file,
you’ll receive
ER2
0036, the “no file found“ error. Follow Table 5 to add a LINK and a
new FILE to your program.
FILE? STEP STEP SP HOUR
MIN
SEC
EVl
EV2 FILE?
#
TYPE
1
8
LINK
.._
5
----_
..~--
5
1
SETPOINT
--_-
_I75
&___-._.
.
0
50..
ON
ON
_~
5 2
SETPOINT
175 0
0
20
ON ON
5. 3
SETPOINT
100 0
1
15
ON OFF
5 4
SETPOINT
100 0
0
10
ON OFF
5
5
SETPOINT
75 0
0
25
OFF OFF
5
6
STOP
Run your program again beginning at FILE
1,
STEP 8. Step through the menu to see
the step type you’re on, and time remaining. See what happens at the end of File
1.
The
WAITFOR
Step
Table 6
-
The
WAITFOR
Step.
FILE STEP
STEP
WPV
WHR
WMN
#
NPE
5 6
WAITFOR
75
-
5 7
STOP
The last step type we will work with is the
WAITFOR
step. This is
a
test step.
It com-
pares a specified temperature with the process temperature, before continuing the
program.
It also waits for programmed time to elapse before continuing with the pro-
gram. After the test is successful, the program continues to the next sequential step.
Return to PROGRAM and enter FILE? (5). Add a
WAITFOR
step to the end of that file.
WHR and WMN are unprogrammed. To program a
WAITFOR
time, enter your values
for WHR and WMN. The programmed
WAITFOR
time waits that time duration. Both
WAITFOR
process variable (WPV), and time
(WHR,WMN)
can be programmed simul-
taneously. Once a
WAITFOR
condition is satisfied, it won’t have to be performed again.
18
Run your program from FILE 5, STEP 1. If you don’t want to go through the entire
program, START your program at any STEP in FILE
1
or 5. When the program reaches
FILE 5, STEP 6, the HOLD LED begins flashing. This means the program is still
running, but is
HOLDing,
to
WAITFOR
the ACTUAL temperature to equal the
WATLOW Series 920 User’s
Manual
Sample
Proqram
Chapter
3
- Series 920 1
- Safety Information 2
- Your Program 3
- Contents 4
- Figures, Tables and Charts 5
- Chapter 1 6
- Starting out with the 6
- Watlow Series 920: 6
- Packing List 7
- How to Open the 920 8
- How to Set the DIP Switches 8
- User’s Manual 9
- Operating 10
- Chapter 11
- Keyboard Area 13
- Where To Go From Here 13
- A Brief Overview 14
- Enter Real Time of Day 14
- Before Entering Your Program 15
- Programming. File 1 15
- Step 4 must be 16
- Editing Your Program 17
- Adding an AUTOSTART Step Type 17
- Running Your Series 920 19
- Chapter 4 20
- How to Check for Ground Loops 22
- Noise Suppression Devices 22
- Available from Watlow 22
- C.M.Line Filter 23
- Installation Information 24
- Installation Procedure 24
- How to Wire the Series 920 25
- Power Wiring 26
- T.C. Compensation 27
- Load from 30
- Temperature Conrol 32
- How to Tune the Series 920 33
- Series 920 User’s 34
- Chapter 6 36
- How To Program The Series 920 36
- Event Outputs 37
- Guaranteed Soak 37
- The Four 38
- JUMPLOOP 38
- Rules to Follow 39
- SYSTEM Menu 40
- .:.:.:.: 41
- SETUP Menu 42
- Represents the 45
- PROGRAM Menu 49
- StepType 50
- To Program 52
- 920, Chapter 6 52
- Chart I- Master Step Chart 53
- Chapter 7 54
- Alarm Types 55
- The Operating Band 56
- Alarm Limits 57
- Clearing An Alarm Message 58
- An Alarm And The State 58
- The Alarm Relay 58
- Appendix 59
- Series 920 Specifications 59
- 920 User’s Manual 60
- 61
- Type J, K, or T 62
- Reference Compen 62
- Equipment Required 63
- Setup and Calibration 63
- @)(sJ(g; 64
- Glossary 67
- Accepts the sensor input and 68
- Isolation: 70
- ON/OFF control: 71
- WATLOW Series 920 73
- Manual 73
- Thermal System: 74
- Safety Information, 2 76
- Warranty Information 77
- Returning Merchandise 77
- Shipping Claims 77
- Series 920 Error Codes/Alarms 78
- Clearing an Error Code 79
- How to Clear an Alarm Code 79
- Series 920 Quick 80
- Reference 80
Related products and manuals for Garden tools Ariens Path-Pro 136E
Garden tools Ariens 920013 Specifications
(40 pages)
(40 pages)
Garden tools Ariens 915501 Service Manual
(44 pages)
(44 pages)
Garden tools Ariens 986101 User Manual
(2 pages)
(2 pages)
Garden tools Ariens 920012 User Manual
(42 pages)
(42 pages)
Garden tools Ariens 920012 User Manual
(42 pages)
(42 pages)
Garden tools Ariens 920013 User Manual
(8 pages)
(8 pages)
Garden tools Ariens 920013 Operator's Manual
(41 pages)
(41 pages)
Garden tools Ariens 920012 User Manual
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.134 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals