Ariens Compact 24 Operator's Manual

Browse online or download Operator's Manual for Garden tools Ariens Compact 24. Ariens Compact 24 Operator`s manual User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 30
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Quick Start Guide
Compact 24 LE (920014 s/n 100000 & up)
Step 1: Assemble Handlebar
Step 2: Install Discharge Chute
Step 3: Install Discharge Chute Crank
Step 4: Install Remote Deflector Cable
Step 5: Check Function of Dual Handle Interlock
Step 6: Check Tire Pressure
Step 7: Adjust Skid Shoes
Step 8: Check Auger Gearcase Oil
Step 9: Check Engine Crankcase Oil
Step 10: Fill Engine Fuel Tank
Step 11: Starting the Engine
Step 12: Stopping the Engine
READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.
IMPORTANT: READ OPERATOR’S MANUAL AND ENGINE MANUAL
THOROUGHLY AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES
BEFORE OPERATING.
Page view 0
1 2 3 4 5 6 ... 29 30

Summary of Contents

Page 1 - Quick Start Guide

Quick Start Guide Compact 24 LE (920014 s/n 100000 & up) • Step 1: Assemble Handlebar • Step 2: Install Discharge Chute • Step 3: Install Discharg

Page 2 - Not attached Attached

Step Three: Install Discharge Chute Crank 1. Remove gear cover from top of chute pedestal. 2. Slide Chute Crank through the nylon bushing in the suppo

Page 3 - (Unfold Lower Handlebar)

Step Four: Install Remote Deflector Cable 1. Pull rubber seal cap away from snap fitting. 2. Install snap fitting into cable bracket’s mounting hole

Page 4

6. Secure cable eye to control lever with sleeve bushing and hairpin. 7. Using the wire hook attached to the deflector cable, hook cable to discharge

Page 5 - (Attach Control Cables)

Step Five: Check Function of Dual Handle Interlock Without the engine running, press down (engage) both clutch levers. Release attachment clutch lever

Page 6 - Assembly)

Step Six: Check Tire Pressure Check tire pressure and adjust to the pressure listed on tire sidewall.

Page 7 - Step One:

Step Seven: Adjust Skid Shoes IMPORTANT: Skid shoes should be adjusted as conditions require. Allow 1/8 in. (3mm) between scraper blade and hard smoot

Page 8 - Assemble Handlebar

Check oil level in auger gearcase (see Check Auger Gearcase in Owners Manual). Step Eight: Check Auger Gearcase Oil

Page 9 - Install Discharge Chute

IMPORTANT: The engine is shipped with oil in crankcase. Refer to Engine Manual for detailed instructions. Step Nine: Check Engine Crankcase Oil

Page 10 - Discharge Chute Crank

Fill fuel tank. DO NOT OVERFILL! See FILLING FUEL TANK in Owners Manual. Remove the plug from the fuel tank and install the fuel cap located in the a

Page 11 - Deflector Cable

Step Eleven: Starting the Engine

Page 12 - Deflector Cable Cont

Step One: Assemble Handlebars NOTE: The Ariens company has made changes to packaging that affects this serial number range. If the upper handlebars

Page 13 - Step Five:

Starting Engine / Step A: Throttle Move the throttle control lever to the fast position. Operate the engine with the throttle control lever in the fas

Page 14 - Check Tire Pressure

Starting Engine / Step B: Fuel Valve Turn the fuel shut-off valve to the “ON” position.

Page 15 - Adjust Skid Shoes

Starting Engine / Step C: Key Insert the key and turn to the on/start position.

Page 16 - Check Auger Gearcase Oil

Starting Engine / Step D: Choke Turn the choke control knob to the choke position. NOTE: Choke is usually unnecessary when restarting a warm engine.

Page 17 - Check Engine Crankcase Oil

Starting Engine / Step E: Prime Push the primer two times. Be sure to cover the vent hole on the primer bulb. NOTE: Priming is usually unnecessary w

Page 18 - Fill Engine Fuel Tank

Starting Engine / Step F: (Manual Start) Firmly hold the starter cord handle. Pull the starter cord handle slowly until resistance is felt, then pull

Page 19

Starting Engine / Step F: (Electric Start) First connect the extension cord to the power cord receptacle and then into a wall receptacle. I

Page 20 - Throttle

Starting Engine / Step G: (Electric Start) Depress the push button. After you start the engine, first disconnect the extension cord from the wall rece

Page 21 - Fuel Valve

Starting Engine / Step H: Warm up Allow the engine to warm up for several minutes. Then, slowly move the choke control knob to the run position.

Page 22 - Starting Engine / Step C:

Step Twelve: Stopping the Engine Turn the key to the off position or move throttle control lever to slow and then to the stop position (completely lef

Page 23 - Starting Engine / Step D:

Step One: Assemble Handlebars (Unfold Lower Handlebar) 1. Remove wheel pins from each side of the unit and slide wheels away from frame. Do not remov

Page 24 - Starting Engine / Step E:

Additional Resources • Refer to Owners Manual and Engine Manual • Contact Ariens Company www.ariens.com Phone: 920-756-4688 E-mail: [email protected]

Page 25 - (Manual Start)

Step One: Assemble Handlebars (Attach Upper Handlebar Assembly) 1. Attach upper handlebar assembly to lower handlebar using two sets of the handlebar

Page 26 - (Electric Start)

Step One: Assemble Handlebars (Attach Control Cables) 1. Hook Spring end of attachment control cable to the clutch arm. 2. Hook spring end of the trac

Page 27 - Starting Engine / Step G:

Step One: Assemble Handlebars (Unfold Upper Handlebar) Assembly) 1. Rotate handlebar into operating position. NOTE: Be careful not to damage cable spr

Page 28 - Warm up

Step One: (Connect Headlight Wire Harness) NOTE: The headlight wire harness comes attached to the upper handlebar assembly. 1. Route the wire harness

Page 29

Step One: Assemble Handlebar 1. Remove the lower and loosen the upper hardware on the handlebar assembly. 2. Loosen the hardware on the shift rod. 3.

Page 30 - Additional Resources

Step Two: Install Discharge Chute 1. Grease underside of discharge chute ring (if not already greased). 2. Remove mounting hardware from auger housing

Comments to this Manuals

No comments