Ariens Path-Pro 136E User Manual Page 36
- Page / 80
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 6
How To Program The Series 920
This chapter will enable you to set up the Series 920 quickly and easily.
It will
explain why it’s a good idea to write out your parameter values.
Chapter 6 also
shows you flow diagrams of the programming process.
Write Out Your Program
The Watlow Series 920 controls temperature for a specific heating and/or cooling
process. Your setup parameter values, when they’re entered, give the Series 920
orders for the work you want it to
perform.
Since the amount of information in the setup is extensive, we suggest that you write
the value on a copy of the Master Step Chart on Page 53. This will enable you to set
up the Series 920 quickly and without mistakes. The chart makes a good record of
your values.
Programming in General
Programming the Series 920 is easy as 1
-
2
-
3:
1. Use the MODE key to select the alphanumeric display prompt you want.
2. Use the UP/DOWN keys to select data or prompts in the alphanumeric display.
3. Press ENTER.
Select the Proper DIP Switch Settings
Prior to programming and operating the Series 920, you must set the DIP Switches.
DIP Switch #1 sets a “warm” or “cold” start following power removal from the 920.
With the DIP switch in the OFF position for a “Warm Start”, the micro-processor uses
previously programmed information as if power had not been removed. A Cold Start
starts “clean” or completely cleared of all user-programmed information when the DIP
switch is in the ON position. All parameters will be empty or set to the default limits.
DIP switch
#2
is not used. Set it to the OFF position.
DIP switch
#3
selects tenths of units displayed for process inputs.
DIP switch
#4
is ON for
0-5VDC/0-20mA
input
&
OFF for
1-5VDC/4-20mA
input.
DIP switch
#5
is for units with
4-20mA
output. If you have this unit, set
#5
to the ON
position.
DIP switch
#6
determines whether the front panel LED’s to the right of the actual
display are load indicators or
OF/%
indicators. When OFF, the
LEDs
are
°F/°C
indicators.
DIP switch
#7, when
OFF, displays all SPCLFUNC parameters. When ON, only
factory selected parameters are displayed.
36
DIP switch
#8
is for factory test and calibration, it must be OFF.
WATLOW
Series 920
User’s
Manual
How To
Program
the Series 920, Chapter 6
- Series 920 1
- Safety Information 2
- Your Program 3
- Contents 4
- Figures, Tables and Charts 5
- Chapter 1 6
- Starting out with the 6
- Watlow Series 920: 6
- Packing List 7
- How to Open the 920 8
- How to Set the DIP Switches 8
- User’s Manual 9
- Operating 10
- Chapter 11
- Keyboard Area 13
- Where To Go From Here 13
- A Brief Overview 14
- Enter Real Time of Day 14
- Before Entering Your Program 15
- Programming. File 1 15
- Step 4 must be 16
- Editing Your Program 17
- Adding an AUTOSTART Step Type 17
- Running Your Series 920 19
- Chapter 4 20
- How to Check for Ground Loops 22
- Noise Suppression Devices 22
- Available from Watlow 22
- C.M.Line Filter 23
- Installation Information 24
- Installation Procedure 24
- How to Wire the Series 920 25
- Power Wiring 26
- T.C. Compensation 27
- Load from 30
- Temperature Conrol 32
- How to Tune the Series 920 33
- Series 920 User’s 34
- Chapter 6 36
- How To Program The Series 920 36
- Event Outputs 37
- Guaranteed Soak 37
- The Four 38
- JUMPLOOP 38
- Rules to Follow 39
- SYSTEM Menu 40
- .:.:.:.: 41
- SETUP Menu 42
- Represents the 45
- PROGRAM Menu 49
- StepType 50
- To Program 52
- 920, Chapter 6 52
- Chart I- Master Step Chart 53
- Chapter 7 54
- Alarm Types 55
- The Operating Band 56
- Alarm Limits 57
- Clearing An Alarm Message 58
- An Alarm And The State 58
- The Alarm Relay 58
- Appendix 59
- Series 920 Specifications 59
- 920 User’s Manual 60
- 61
- Type J, K, or T 62
- Reference Compen 62
- Equipment Required 63
- Setup and Calibration 63
- @)(sJ(g; 64
- Glossary 67
- Accepts the sensor input and 68
- Isolation: 70
- ON/OFF control: 71
- WATLOW Series 920 73
- Manual 73
- Thermal System: 74
- Safety Information, 2 76
- Warranty Information 77
- Returning Merchandise 77
- Shipping Claims 77
- Series 920 Error Codes/Alarms 78
- Clearing an Error Code 79
- How to Clear an Alarm Code 79
- Series 920 Quick 80
- Reference 80
Related products and manuals for Garden tools Ariens Path-Pro 136E
Garden tools Ariens 920013 Specifications
(40 pages)
(40 pages)
Garden tools Ariens 915501 Service Manual
(44 pages)
(44 pages)
Garden tools Ariens 986101 User Manual
(2 pages)
(2 pages)
Garden tools Ariens 920012 User Manual
(42 pages)
(42 pages)
Garden tools Ariens 920012 User Manual
(42 pages)
(42 pages)
Garden tools Ariens 920013 User Manual
(8 pages)
(8 pages)
Garden tools Ariens 920013 Operator's Manual
(41 pages)
(41 pages)
Garden tools Ariens 920012 User Manual
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.790 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals