Owner/Operator ManualManuel Du Propriétaire/UtilisateurModels926045 – Power Brush 36(Serial No. 35000 and up)Power Brush 3604394300 9/11Printed in USA
GB - 101. Traction Drive Clutch Lever2. Speed Selector Lever3. Attachment Clutch Lever4. Brush Angle Lock Lever5. Recoil Starter Handle6. Engine Shut
GB - 11STANDARD CONTROLSSee Controls and Features on page 10.Traction Drive Clutch - Left Hand LeverSqueeze the Traction Drive Clutch Lever against th
GB - 12Throttle LeverThe throttle controls the engine speed. To increase or decrease engine speed, adjust to:1. Fast (normal or warm starts) to left2
GB - 134. Stop engine and allow all moving parts to stop.5. Check the width of the swept area. The brush pattern should be 2-3 inches (5.08-7.6 cm) wi
GB - 14Fuel StabilizerGasoline left in the fuel system for extended periods without a stabilizer will deteriorate, resulting in gum deposits in the sy
GB - 155. If engine is cold, apply choke. A warm engine requires less choking than a cold engine. See Engine Manual for detailed instructions. 6. Set
GB - 16Ariens Dealers will provide any service or adjustments which may be required to keep your unit operating at peak efficiency. Should engine serv
GB - 17OPERATING POSITION(Figure 7)To connect the brush attachment to traction unit:1. Place attachment belts onto attachment pulley.NOTE: Holding dow
GB - 18CHECK CLUTCH OPERATIONBrush must stop quickly when attachment clutch lever is released.Wheels must stop quickly when traction drive clutch leve
GB - 19GENERAL LUBRICATION(Figure 8)1. Place unit into the service position (See Service Position on page 16).IMPORTANT: Wipe each fitting clean befor
GB - 20Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Assembly . . . . . . . . . . . . . . . . . . . . . . . . 8Controls & Feature
GB - 20RECOIL GUARD FOAM COVER INSTALLATION(Figure 9)The recoil foam cover slides over the starter handle and attaches to the recoil guard with Velcro
GB - 21ATTACHMENT CLUTCH/BRAKE ADJUSTMENT(Figures 11, 12 and 13)Remove Attachment Cable Slack1. Remove the belt cover.2. Loosen jam nut on cable adjus
GB - 22Check Attachment Brake(Figure 14)1. With the attachment clutch lever disengaged, brake pad must contact attachment belt. With attachment clutch
GB - 23TRACTION DRIVE CLUTCH ADJUSTMENT(Figure 16)If drive slips, adjust traction clutch to compensate for friction disc wear.To adjust traction clutc
GB - 244. Remove traction drive belt from drive plate assembly pulley (Figure 18).5. Install new traction drive belt (Part Number 07231000) onto drive
GB - 25BRUSH SEGMENT REPLACEMENT(Figure 19, 20, et 21)1. Shut off engine, close fuel shut-off valve, disconnect spark plug wire and allow unit to cool
GB - 263. Loosen each bearing setscrew and slide bearings inward, away from horizontal end supports.IMPORTANT: Brush gearbox splined shaft will separa
GB - 2712. Slide brush shaft bearings outward, against brush housing. Tighten each bearing setscrew to lock it in place on center shaft.13. Install tw
GB - 28]To obtain a complete parts manual, find your model and serial number. Then go to www.ariens.com.TROUBLESHOOTINGPROBLEM PROBABLE CAUSE CORRECTI
GB - 29SPECIFICATIONSModel Number 926045Engine Subaru EX27Engine Displacement - in3 (cc)16.2 (265)Fast Idle Speed-RPM 3800 ±100Starter 120VAC Electric
GB - 3• Record Unit Model and Serial number here.• Record Engine Model and Serial number here.PRODUCT REGISTRATIONThe Ariens dealer must register the
Sno-Chore_2011.B30Sno-Thro®, Sno-Tek® and Chore Performing Equipment Limited WarrantyAriens Company (Ariens) warrants to the original purchaser that A
Sno-Chore_2011.B31Exceptions and LimitationsThe chart below details special exceptions to this warranty:Customer ResponsibilitiesRegister the product
Sno-Chore_2011.B32Exclusions - Items Not Covered by This Warranty• Parts that are not genuine Ariens, Gravely, Parker or Countax service parts are not
CARB_EPA_201133 CALIFORNIA AND EPA (UNITED STATES ENVIRONMENTAL PROTECTION AGENCY) EVAPORATIVE EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS
CARB_EPA_201134(4.) Repair or replacement of any warranted part under the warranty provisions of this article must be performed at no charge to the ow
Ariens Company655 West Ryan StreetBrillion, WI 54110-1072920-756-4688Fax 920-756-2407www.ariens.com
GB - 4SAFETY ALERT SYMBOLThese are safety alert symbols. They mean: • ATTENTION! • YOUR SAFETY IS INVOLVED! When you see this symbol:• BECOME ALERT!
GB - 5 1. WARNING! 2. CAUTION! 3. DANGER! 4. HOT SURFACES!EMISSION CONTROL SYSTEMThis equipment and/or its engine may include exhaust and evaporative
GB - 6NEVER allow children to operate or play on or near unit. Be alert and shut off unit if children enter area.DO NOT allow adults to operate unit w
GB - 7ALWAYS remove key to prevent unauthorized use.Never carry passengers.Adjust brush height before operating. Engage traction drive clutch before a
GB - 8Tools Required:•Tire Gauge• Pliers• 1/2-In. 3/8-In, 7/16-In, and 9/16-In Wrench and/or Adjustable WrenchUnpacking UnitUnfold Handlebar(Figure 3)
GB - 9Check Tire PressureCheck tire pressure and adjust to the pressure listed on tire sidewall.Check Engine Crankcase OilIMPORTANT: Engine is shipped
Comments to this Manuals