Ariens 920013 Specifications

Owner/Operator ManualManuel Du Propriétaire/UtilisateurModels920013 – Compact 22 LE(Serial No. 35000 and up)920014 – Compact 24 LE(Serial No. 35000 an

GB - 10Install Remote Deflector Cable (920014)(Figure 7 and 8)1. Slide cable through clip on top of discharge chute pedestal (Figure 7).2. Bend clip c

GB - 11Check Tire PressureCheck tire pressure and adjust to the pressure listed on tire sidewall.Check Auger Gearcase OilCheck oil level in auger gear

GB - 121. Attachment Clutch Lever2. Speed Selector3. Traction Drive Clutch Lever4. Chute Crank 5. Muffler Guard6. Chute Deflector Cap7. Discharge Chut

GB - 131. Gas Tank and Cap2. Oil Fill and Dipstick3. Fuel Shut-off Valve4. Recoil Starter Handle5. Electric Starter6. Throttle7. Choke8. Ignition Swit

GB - 14CONTROLS AND FEATURESSee Figure 9 and 10 for all Controls and Features locations.Dual Handle Interlock When Attachment Clutch and then Traction

GB - 15Speed SelectorPosition the Speed Selector in the appropriate speed notch to control forward and reverse travel.Forward:(6) Fastest(1) SlowestRe

GB - 16Snow Clean-Out Tool (Figure 13)To clear the discharge chute:1. Shut off the engine.2. Wait 10 seconds and make sure impeller blades have stoppe

GB - 17Scraper BladeThe scraper blade allows the back of the housing to keep better contact with the surface being cleared. It also prevents damage to

GB - 18If clutches do not engage or disengage properly, adjust or repair before operation (see Attachment Clutch/Brake Adjustment on page 25 and Attac

GB - 198. If engine is cold, apply choke. A warm engine requires less choking than a cold engine. See Engine Manual for detailed instructions. 9. 9200

GB - 2SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . 4ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . 8CONTROLS and FEATURES . . . .

GB - 20Ariens Dealers will provide any service or adjustments which may be required to keep your unit operating at peak efficiency. Should engine serv

GB - 21CHECK CLUTCH OPERATIONAuger / impeller must stop within 5 seconds when attachment clutch/impeller brake lever is released.Wheels must stop quic

GB - 22GENERAL LUBRICATION(Figure 17)IMPORTANT: Wipe each fitting clean before and after lubrication. IMPORTANT: DO NOT allow grease or oil to get on

GB - 23SCRAPER BLADEIMPORTANT: Damage to housing will result if blade wears down too far. Scraper blade is adjustable to compensate for wear.To adjust

GB - 24MANUAL DISCHARGE CHUTE DEFLECTOR (920013)(Figure 20)Deflector must stay in selected position while throwing snow.To adjust, loosen then retight

GB - 25SPEED SELECTOR ADJUSTMENT(Figure 24)To adjust:1. Disconnect adjustment pivot pin from speed selector arm. Save hardware for reinstallation.2. P

GB - 264. With the attachment clutch disengaged, check that the attachment idler arm lightly touches the frame (Figure 26).5. Tighten jam nut on cable

GB - 27Check Attachment Brake (Figure 29)1. With the clutch lever disengaged, brake pad must contact attachment belt. With clutch lever engaged, brake

GB - 28IMPORTANT: To avoid bending bottom cover, when tipping unit apart, support handlebars firmly or tip unit up on housing and remove bottom cover

GB - 29TRACTION DRIVE BELT REPLACEMENT(Figures 34)NOTE: Housing and frame must be tipped apart and attachment drive belt removed from engine sheave in

GB - 3• Record Unit Model and Serial numbers here.• Record Engine Model and Serial numbers here.PRODUCT REGISTRATIONThe Ariens dealer must register th

GB - 3013. Insert new friction disc assembly into frame. Install washers onto carrier bearing and slide into speed selector arm. 14. Slide hex shaft t

GB - 315. Run the engine outdoors for 1 minute to be sure that treated gasoline has replaced the untreated gasoline in the carburetor.6. Slow the engi

GB - 32Engine problems.1. See Engine Manual. 1. See Engine Manual.Does not operate in Forward / Reverse.1. Friction disc worn out.2. Traction belt not

GB - 33SPECIFICATIONSModel Number 920013Description Compact 22Engine Ariens OHVGross Torque* - ft-lbs (N-m) 9.5 (12.88)*Engine output stated in gross

GB - 34SPECIFICATIONSModel Number 920014Description Compact 24Engine Briggs & Stratton Polar ForceGross Torque* - ft-lbs (N-m) 9.0 (12.2)*Engine

Sno-Chore_2011.B35Sno-Thro®, Sno-Tek® and Chore Performing Equipment Limited WarrantyAriens Company (Ariens) warrants to the original purchaser that A

Sno-Chore_2011.B36Exceptions and LimitationsThe chart below details special exceptions to this warranty:Customer ResponsibilitiesRegister the product

Sno-Chore_2011.B37Exclusions - Items Not Covered by This Warranty• Parts that are not genuine Ariens, Gravely, Parker or Countax service parts are not

CARB_EPA_201138 CALIFORNIA AND EPA (UNITED STATES ENVIRONMENTAL PROTECTION AGENCY) EVAPORATIVE EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS

CARB_EPA_201139(4.) Repair or replacement of any warranted part under the warranty provisions of this article must be performed at no charge to the ow

GB - 4SAFETY ALERTSLook for these symbols to point out important safety precautions. They mean:Attention! Personal Safety Is Involved!Become Alert!

Ariens Company655 West Ryan StreetBrillion, WI 54110-1072920-756-4688www.ariens.com

GB - 51. WARNING!2. DANGER! 3. DANGER!EMISSION CONTROL SYSTEMThis equipment and/or its engine may include exhaust and evaporative emissions control sy

GB - 6Keep children and people away. Keep children out of work area and under watchful care of a responsible adult.NEVER allow children to operate or

GB - 7Disengage attachment when not in use. Disengage all clutches before starting engine. Adjust skid shoes to clear gravel or crushed rock surfaces

GB - 8PACKAGE CONTENTSASSEMBLYTools Required:• Pliers• Open-End Wrenches: 3/8, 7/16, 1/2, 9/16 in. and/or Adjustable Wrench•Tire GaugeUnfold Handlebar

GB - 9Install Discharge Chute(Figure 5)1. Grease underside of discharge chute ring (if not already greased).2. Remove mounting hardware from the botto