Ariens Path-Pro 136E User Manual Page 48
- Page / 80
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
RETURN
1
Determines whether the alarm type for Auxiliary Output
1
will be a process
alarm
or a deviation
alarm for the Series
920.
This parameter will not appear if
AUX1
=
AL, or DIP switch
#7
is ON.
Range:
Alpha
Display
Alarm Type
Default: P
ALTYP1
P
Process Alarm
ALTYP1
D
Deviation Alarm
Determines whether the alarm type for Auxiliary Output 2 will be a process
alarm
or deviation
alarm. This parameter will not appear if AUX2
=
AL, or DIP switch
#7
is ON.
Range:
Alpha
Display
Alm
Type
Default: P
ALTYP2 P
Process Alarm
ALTYP2 D
Deviation Alarm
Selects alarms as latching or non-latching. Latching remains energized until you manually clear it.
This parameter will not appear if DIP switch
#7
is ON.
Range:
LAT
or
NLAT
Default:
NLAT
Allows the operator to change the input gain of the
RTD
Input for diierent curves. This parameter
will not appear if the input type is not RTD whole or RTD tenths, or DIP switch
#7
is ON.
Range:
JIS
or DIN
Default:
JIS
Selects the minimum percent of power that the
Series
920 will output. This parameter will not
appear if DIP switch
#7
is
ON,
Range: 0 to
100%
Default: 0
Selects
the
maximum percent of power that the
Series
920 will output. This parameter will not
appear
if DIP switch
#7
is ON.
Range: 0 to 100%
Default: 100
The Guaranteed Soak parameter guarantees the actual temperature is being controlled within a
window around set point.
lf
exceeded, the step time clock stops and the HOLD LED flashes until
the actual temperature is within the soak window.
Range: 0 to
90°F/
to
50°C
Default: 0
Represents the selection of the protocol type for serial communications. This selects
XON/XOFF
protocol or ANSI X3.28 communication protocol. This parameter will not appear if your Series 920
does not have communications.
Range: STX or XON
Default: STX
Represents the device identification number as required for the ANSI X3.28 communications
protocol for the Series 920. This parameter will not appear if
COM
has been selected as
XON,
or if
your Series 920 does not have communications.
Refer
to the 920 Data Communications Manual.
Range: 0 to 9
Default: 0
Allows for specific groups of parameters to be unaffected by the UP/DOWN and ENTER keys,
preventing these parameters from being changed accidentally.
0
=
No lock, full access of all parameters.
1
=
Prevents user from editing all parameters except the SYSTEM parameter group, the LOCK
parameter, the STEP and FILE parameter in the PROGRAM and
pre-RUN
groups.
2 -Prevents user from editing all parameters except
ER1
,
ER2,
&
ALRM
in the SYSTEM menu,
and the LOCK, STEP and FILE parameter are in the PROGRAM and
pre-RUN
menus.
Range: 0
-
2
Default: 0
Allows the operator to clear a file of the Series 920.Press ENTER, and choose the FILE? to clear.
Range:
1
-
10
Default:
1
From RETURN, you can go back to the SYSTEM prompt by pressing the ENTER key, or return to
SPCLFUNC by pressing the MODE key.
48
WATLOW
Series
920 User’s Manual
How To
Proqram
the Series
920,
Chapter 6
- Series 920 1
- Safety Information 2
- Your Program 3
- Contents 4
- Figures, Tables and Charts 5
- Chapter 1 6
- Starting out with the 6
- Watlow Series 920: 6
- Packing List 7
- How to Open the 920 8
- How to Set the DIP Switches 8
- User’s Manual 9
- Operating 10
- Chapter 11
- Keyboard Area 13
- Where To Go From Here 13
- A Brief Overview 14
- Enter Real Time of Day 14
- Before Entering Your Program 15
- Programming. File 1 15
- Step 4 must be 16
- Editing Your Program 17
- Adding an AUTOSTART Step Type 17
- Running Your Series 920 19
- Chapter 4 20
- How to Check for Ground Loops 22
- Noise Suppression Devices 22
- Available from Watlow 22
- C.M.Line Filter 23
- Installation Information 24
- Installation Procedure 24
- How to Wire the Series 920 25
- Power Wiring 26
- T.C. Compensation 27
- Load from 30
- Temperature Conrol 32
- How to Tune the Series 920 33
- Series 920 User’s 34
- Chapter 6 36
- How To Program The Series 920 36
- Event Outputs 37
- Guaranteed Soak 37
- The Four 38
- JUMPLOOP 38
- Rules to Follow 39
- SYSTEM Menu 40
- .:.:.:.: 41
- SETUP Menu 42
- Represents the 45
- PROGRAM Menu 49
- StepType 50
- To Program 52
- 920, Chapter 6 52
- Chart I- Master Step Chart 53
- Chapter 7 54
- Alarm Types 55
- The Operating Band 56
- Alarm Limits 57
- Clearing An Alarm Message 58
- An Alarm And The State 58
- The Alarm Relay 58
- Appendix 59
- Series 920 Specifications 59
- 920 User’s Manual 60
- 61
- Type J, K, or T 62
- Reference Compen 62
- Equipment Required 63
- Setup and Calibration 63
- @)(sJ(g; 64
- Glossary 67
- Accepts the sensor input and 68
- Isolation: 70
- ON/OFF control: 71
- WATLOW Series 920 73
- Manual 73
- Thermal System: 74
- Safety Information, 2 76
- Warranty Information 77
- Returning Merchandise 77
- Shipping Claims 77
- Series 920 Error Codes/Alarms 78
- Clearing an Error Code 79
- How to Clear an Alarm Code 79
- Series 920 Quick 80
- Reference 80
Related products and manuals for Garden tools Ariens Path-Pro 136E
Garden tools Ariens 920013 Specifications
(40 pages)
(40 pages)
Garden tools Ariens 915501 Service Manual
(44 pages)
(44 pages)
Garden tools Ariens 986101 User Manual
(2 pages)
(2 pages)
Garden tools Ariens 920012 User Manual
(42 pages)
(42 pages)
Garden tools Ariens 920012 User Manual
(42 pages)
(42 pages)
Garden tools Ariens 920013 User Manual
(8 pages)
(8 pages)
Garden tools Ariens 920013 Operator's Manual
(41 pages)
(41 pages)
Garden tools Ariens 920012 User Manual
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 2.845 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals