Ariens Path-Pro 136E User Manual Page 45
- Page / 80
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
One of three main
level
operating menus.
From the SETUP menu, you can setup or
change system-operating parameters such as
real
time,
high/low
range, alarm types,
alarm points,
PID
settings
and communications.
You must select each ACCESS
number to create the personality of your Series
920.
1
ACCESS
(0)
1
ACCESS number (0) must be selected to enter the personality of your Series 920 into
the
CALIB
parameters.
CALIB
1
1
Tl
00:00
1
In the Series 920, when ACCESS (0) is entered under the SETUP menu, the
CALIB
parameters appear. These parameters set up the Real Time clock, alarms, and the
calibration offset of the process variable.
Represents the
current
Real Time hours and minutes of the Series 920s System.
Midnight
=
0 hours and 0 minutes. A Read Only parameter.
Represents the SYSTEM 24 hour time-ofday
clock
for hours.
Midnight
=
0 hours.
Range: 0
-
23 hours
Default: 0
The SYSTEM 24 hour
time-of-day
clock setting for minutes.
Range: 0 - 59 minutes Default: 0
1
CAL
()
An offset of the process variable. This number is added to the value that the system
derives. The final result is used for the control
point.
Range: -50 to
50°C/-90
to
9O°F
Default: 0
The Series 920 will display this parameter
represetin9
the high process alarm or high
deviation alarm for Alarm
1.
Displayed only when AUX 1
=
AL. See Page 43.
This parameter represents the low process alarm or low deviation alarm for Alarm 1 of
the Series 920. Displayed only when AUX1
=
AL
See Page 43.
Represents the high process alarm or high deviation alarm for Alarm 2 of the Series
920. Displayed only when
AUX2
=
AL. See Page 43.
The low process
alarm
or low deviation alarm for
Alarm
2 of the
Series
920.
Displayed
only when AUX2
=
AL. See Page 43.
From RETURN, you can go back to the SYSTEM prompt by pressing the ENTER key,
or return to ACCESS (0) menu by pressing the MODE key.
In the SETUP menu, ACCESS (1) must be selected to enter the
PID
parameters.
When ACCESS (1) is entered under the SETUP menu of the Series 920, the
PID
parameters will appear. These parameters consist of
Proportional,
Integral (auto
reset), and Derivative (rate) actions.
A proportional temperature band expressed in degrees within which a temperature
controller proportioning function is active for heating. Expressed in degrees. This
parameter will not appear if OUT
=
CL.
Range: 0 to
900°F/0
to
500°C
Default:
45°F/25°C
A reset (integral) heating control action that
automatically
eliminates offset, or “droop”,
between set point and actual process
temperature
in
a proportional control. Expressed
by repeats per minute. This parameter isn’t displayed if OUT
=
CL, or PB H is set to 0.
Range: 0.00 to 5.00 repeats/minute
Default: 0.00
The rate (derivative) heating function of the Series
920.
The rate is determined by how
fast the error being corrected is increasing.
Expressed in minutes. This parameter will
not appear if OUT=CL, or PBH=0.
Range: 0.00 to 5.00 minutes
Default: 0.00
How To Program the Series 920, Chapter 6
WATLOW
Series
920 User’s Manual 45
45
- Series 920 1
- Safety Information 2
- Your Program 3
- Contents 4
- Figures, Tables and Charts 5
- Chapter 1 6
- Starting out with the 6
- Watlow Series 920: 6
- Packing List 7
- How to Open the 920 8
- How to Set the DIP Switches 8
- User’s Manual 9
- Operating 10
- Chapter 11
- Keyboard Area 13
- Where To Go From Here 13
- A Brief Overview 14
- Enter Real Time of Day 14
- Before Entering Your Program 15
- Programming. File 1 15
- Step 4 must be 16
- Editing Your Program 17
- Adding an AUTOSTART Step Type 17
- Running Your Series 920 19
- Chapter 4 20
- How to Check for Ground Loops 22
- Noise Suppression Devices 22
- Available from Watlow 22
- C.M.Line Filter 23
- Installation Information 24
- Installation Procedure 24
- How to Wire the Series 920 25
- Power Wiring 26
- T.C. Compensation 27
- Load from 30
- Temperature Conrol 32
- How to Tune the Series 920 33
- Series 920 User’s 34
- Chapter 6 36
- How To Program The Series 920 36
- Event Outputs 37
- Guaranteed Soak 37
- The Four 38
- JUMPLOOP 38
- Rules to Follow 39
- SYSTEM Menu 40
- .:.:.:.: 41
- SETUP Menu 42
- Represents the 45
- PROGRAM Menu 49
- StepType 50
- To Program 52
- 920, Chapter 6 52
- Chart I- Master Step Chart 53
- Chapter 7 54
- Alarm Types 55
- The Operating Band 56
- Alarm Limits 57
- Clearing An Alarm Message 58
- An Alarm And The State 58
- The Alarm Relay 58
- Appendix 59
- Series 920 Specifications 59
- 920 User’s Manual 60
- 61
- Type J, K, or T 62
- Reference Compen 62
- Equipment Required 63
- Setup and Calibration 63
- @)(sJ(g; 64
- Glossary 67
- Accepts the sensor input and 68
- Isolation: 70
- ON/OFF control: 71
- WATLOW Series 920 73
- Manual 73
- Thermal System: 74
- Safety Information, 2 76
- Warranty Information 77
- Returning Merchandise 77
- Shipping Claims 77
- Series 920 Error Codes/Alarms 78
- Clearing an Error Code 79
- How to Clear an Alarm Code 79
- Series 920 Quick 80
- Reference 80
Related products and manuals for Garden tools Ariens Path-Pro 136E
Garden tools Ariens 920013 Specifications
(40 pages)
(40 pages)
Garden tools Ariens 915501 Service Manual
(44 pages)
(44 pages)
Garden tools Ariens 986101 User Manual
(2 pages)
(2 pages)
Garden tools Ariens 920012 User Manual
(42 pages)
(42 pages)
Garden tools Ariens 920012 User Manual
(42 pages)
(42 pages)
Garden tools Ariens 920013 User Manual
(8 pages)
(8 pages)
Garden tools Ariens 920013 Operator's Manual
(41 pages)
(41 pages)
Garden tools Ariens 920012 User Manual
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.409 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals