Ariens 932 Series Service Manual download pdf (Page 13)

4 - 13

Ariens dealers will provide any service or adjustments

which may be required to keep your unit operating at

peak efficiency. Should engine service be required,

contact an Ariens dealer or an authorized engine

manufacturer's service center.

4.2 SERVICE POSITIONS

Place unit on a flat level surface. Tip unit forward onto

front of impeller housing for service. Assure unit is

secure and will not tip over. Strap and clamp onto

bench if needed.

4.3 TO STOP IN AN EMERGENCY

Immediately release both control levers to stop unit in

an emergency. Stop engine, remove key and wait for

all rotating parts to stop before leaving operator’s

position.

4.4 STARTING AND SHUT OFF

IMPORTANT: Allow unit and engine to adjust to the

outdoor temperatures before clearing snow. Before

shut-off, run the attachment a few minutes to prevent

freeze-up.

IMPORTANT: Try out each control without the engine

running to see how it works and what it does.

Manual Start

1. Turn discharge chute straight ahead.

2. Make sure that the traction clutch and attachment

drive clutch levers are fully disengaged.

3. Push primer bulb 2 or 3 times for cold engine.

NOTE: When temperature is below -15° F (-26° C)

additional priming may be needed.

4. If engine is cold, apply choke. See Engine Manual

for detailed instructions.

NOTE: A warm engine requires less choking than a

cold engine.

5. Set throttle to proper starting position.

6. Insert key into ignition switch and push into RUN

position. DO NOT twist key after it is inserted.

7. Grasp starter handle and pull rope out slowly until it

pulls harder. Let rope rewind slowly.

8. Pull rope with a rapid continuous full arm stroke.

Let rope rewind slowly.

IMPORTANT: DO NOT let starter handle snap against

starter.

9. Repeat steps 7 and 8 until engine starts. (If engine

does not start, refer to Troubleshooting.)

10.Adjust choke as needed.

11.Set throttle to PART THROTTLE or SLOW position

for adaptation to outside temperature or travel. Set

throttle to FAST position for normal operation.

Electric Start

1. Connect extension cord to prongs on starter.

IMPORTANT: Prevent damage to unit. Know voltage of

your starter and only use matching outlets.

2. Plug extension into 120V or 240V 3-wire, grounded

outlet.

3. Turn discharge chute straight ahead.

4. Make sure that the traction clutch and attachment

drive clutch levers are fully disengaged.

5. Push primer bulb 2 or 3 times for cold engine.

NOTE: When temperature is below -15° F (-26° C)

additional priming may be needed.

6. Insert key into ignition switch on engine and push

into RUN position. DO NOT twist key after it is

inserted.

7. If engine is cold, apply choke. A warm engine

requires less choking than a cold engine. See

Engine Manual for detailed instructions.

8. Set throttle to proper starting position.

9. Press starter button on engine until engine starts.

IMPORTANT: DO NOT operate starter more than 15

seconds per minute, as overheating and damage can

occur. (If engine does not start, refer to

Troubleshooting.)

10.Adjust choke as needed.

11.Disconnect power cord from outlet, then starter.

12.Set throttle to PART THROTTLE or SLOW position

for travel or adaptation to outside temperature.

Once achieved, set throttle to FAST position for

normal operation.

Shut Off

1. Release traction drive clutch lever and allow unit to

come to a complete stop.

2. Run Impeller a few minutes after use to prevent

freeze-up of Impeller.

3. Release attachment clutch lever and wait for all

moving parts to come to a complete stop.

4. Move throttle to the STOP position.

5. Remove key.

WARNING: AVOID INJURY. Read and

understand the entire Safety section before

proceeding.

WARNING: Before tipping unit up onto housing,

remove fuel so no spills will occur and remove

battery (if equipped). Ensure unit is secure and

will not tip over during maintenance.

WARNING: FAILURE TO FOLLOW

INSTRUCTIONS could result in personal injury

and/or damage to unit. DO NOT attempt to start

your unit at this time. Read entire Owner/

Operator Manual and the Engine Manual first.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 33 34

Comments to this Manuals

No comments

Ariens 932 Series Service Manual Page 13

Comments to this Manuals

Related products and manuals for Snow throwers Ariens 932 Series