Owner/Operator ManualModels926302 – ST1332LE926310 – ST9526DLE926311 – ST11528DLE926312 – ST1332DLE926313 – ST1336DLE926314 – ST9526DLET926315 – ST115
GB - 10PACKAGE CONTENTSASSEMBLYTools Required:• Pliers• Open-End Wrenches: 3/8, 7/16, 1/2, 9/16 in. and/or Adjustable Wrench•Tire GaugeUnfold Handleba
GB - 11(Figure 6, 7)4. Remove the cover from the gear assembly on the discharge chute.5. Release the lock teeth on the gear assembly with your finger
GB - 12NOTE: Press down on lock teeth with your finger to align the cable ball end with the slot (Figure 8). 10. Replace the gear cover removed in ste
GB - 13Check Track Tension (926314, 315, 316)Check tracking of unit with the differential locked, and tension of tracks (see Track Tension Adjustment
GB - 141. Attachment Clutch Lever2. Speed Selector3. Deflector Remote Control 4. Chute Control 5. Traction Drive Clutch Lever6. Oil Fill/Dipstick7. Mu
GB - 151. Attachment Clutch Lever2. Speed Selector3. Deflector Remote Control4. Chute Control5. Traction Drive Clutch Lever6. Oil Fill/Dipstick7. Disc
GB - 16CONTROLS AND FEATURESSee CONTROLS and FEATURES on page 14 for all Controls and Features locations.Dual Handle Interlock When Attachment Clutch
GB - 17Forward:(6) Fastest(1) Slowest Reverse: (1) Slow(2) FastIMPORTANT: DO NOT change motion from forward to reverse with clutch engaged. Forward sp
GB - 18Discharge Chute ControlIMPORTANT: If chute does not stay in set position, adjust as directed in SERVICE AND ADJUSTMENTS on page 26, or repair
GB - 19Scraper BladeThe scraper blade allows the back of the housing to keep better contact with the surface being cleared. It also prevents damage to
2Ariens Company655 West Ryan StreetBrillion, Wisconsin 54110-1072 USATelephone (920) 756-2141Facsimile (920) 756-2407EC DECLARATION OF CONFORMITY ISSU
GB - 20FILLING FUEL TANKFuel Shut-Off ValveIMPORTANT: The fuel shut-off valve MUST be in the closed position prior to transporting the unit.The fuel s
GB - 21 2. Check Function of ClutchesIf clutches do not engage or disengage properly, adjust or repair before operation. See Attachment Clutch/Brake A
GB - 22Electric Start (240V)1. Connect extension cord to starter.IMPORTANT: Prevent damage to unit. Know voltage of your starter and only use matching
GB - 232. 926302, 310, 311, 312, 313: Press down on handlebars enough to raise front of unit slightly off surface. 926314, 315, 316: Place the unit in
GB - 24CHECK DUAL HANDLE INTERLOCK Without the engine running, press down (engage) both clutch levers. Release attachment clutch lever. Attachment clu
GB - 25Auger ShaftNOTE: To grease auger shaft, remove shear bolt nuts, and shear bolts. Apply grease at the grease zerks and then turn the auger shaft
GB - 264. Replace the cover plate and secure in position with the two screws removed in step 1.NOTE: Make sure the wire harness does not get pinched b
GB - 27For Replacement:1. Align shear bolt holes in auger with shear bolt holes in the shaft.2. Drive shear bolt through hole (if shear bolt was broke
GB - 287. Check and adjust attachment clutch, speed selector and traction clutch. See Speed Selector Adjustment on page 29 and Traction Drive Clutch A
GB - 29If chute does not rotate freely:Tighten the cable by loosening the upper adjustment nut, and then tightening the lower adjustment nut against t
3CE Sound and Vibration – Bruits et vibrations CE – CE Geräusch- und Vibrationswerte – CE Geluid en trilling – CE støj og vibration – Livello sonoro e
GB - 303. With the attachment clutch disengaged, check that the attachment idler arm lightly touches the frame. See Figure 33.4. Tighten jam nut on th
GB - 31Adjust the Attachment Clutch Cable Spring Extension1. Check the attachment clutch cable spring extension. Measure the length of the attachment
GB - 322. If there is less than 1/16 in. (1.6 mm) gap between brake pad and belts, follow these steps:a. To increase brake pad gap, loosen idler adjus
GB - 335. Adjust spring extension.a. With the traction drive clutch lever disengaged, loosen the jam nut on the cable adjuster.b. Turn the adjuster bo
GB - 34Install new attachment drive belts:1. Place new attachment belts onto attachment pulley.NOTE: Holding down the attachment clutch lever will mak
GB - 359. Install pinion sprocket and chain on hex shaft, then replace bearing flanges.10. Hold wheel so friction disc will not rotate and secure new
GB - 363. Turn the adjustment barrel to remove all cable slack and bring the overtravel arm until it makes slight contact with the right end of the sl
GB - 37 SERVICE PARTSOrder the following parts through your Dealer:Part No. Description00036800 Ariens Hi-Temp Grease (3, 3 oz. cartridges)00592900 Fu
GB - 38 TROUBLESHOOTINGPROBLEM PROBABLE CAUSE CORRECTION Engine will not crank/start.1. Fuel tank is empty.2. Fuel shut-off valve closed.3. Build up o
GB - 39SPECIFICATIONSModel Number 926302 926310 926311 926312DescriptionST1332LE ST9526DLE ST11528DLE ST1332DLEEngine - TecumsehOH358SATecumsehOH318S
GB - 4SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . 5ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . 10CONTROLS and FEATURES. . . .
GB - 40SPECIFICATIONSModel Number 926313 926314 926315 926316DescriptionST1336DLE ST9526DLET ST11528DLET ST1332DLETEngine - TecumsehOH358SATec umsehO
Ariens Company655 West Ryan StreetBrillion, WI 54110-1072920-756-2141Fax 920-756-2407www.ariens.com
GB - 5UNAUTHORIZED REPLACEMENT PARTSUse only Ariens replacement parts. The replacement of any part on this vehicle with anything other than an Ariens
GB - 6 NOTATIONSNOTE: General reference information for proper operation and maintenance practices.IMPORTANT: Specific procedures or information requi
GB - 72. DANGER! 3. DANGER!SAFETY RULESRead, understand, and follow all safety practices in Owner/Operator Manual before beginning assembly or operati
GB - 8ALWAYS keep hands away from all pinch points.DO NOT touch unit parts which might be hot from operation. Allow parts to cool before attempting to
GB - 9Fuel is highly flammable and its vapors are explosive. Handle with care. Use an approved fuel container.NO smoking, NO sparks, NO flames. ALWAYS
Comments to this Manuals