Ariens 932 Series Service Manual

932 Sno-Thro02965700 05/07Printed in USAService ManualModels 932045, 932046, 932047, 932048, 932311, 932312

2 - 10StorageDO NOT store unit inside a building with fuel in the fuel tank where any ignition sources are present. Allow unit to cool completely befo

3 - 11SECTION 3 - SPECIFICATIONSModel Number 932045 932046 932047 932048EngineBriggs 15A1930118E1Tecumseh OH195SATecumseh LH195SPTecumseh LH195SPPower

3 - 12SPECIFICATIONSModel Number 932311 932312DescriptionST5520 ST7524Engine - Tecu msehOH195SATecum sehOH195SPPower Max - HP (kW) 5.5 (4.1) 7.5 (5.6

4 - 134.1 CONTROLS AND FEATURES1. Attachment Clutch Lever2. Speed Selector3. Traction Drive Clutch Lever4. Chute Crank5. Muffler Guard6. Discharge Ch

4 - 141. Attachment Clutch Lever2. Speed Selector3. Traction Drive Clutch Lever4. Chute Crank5. Discharge Chute Deflector6. Discharge Chute7. Impeller

4 - 15Ariens dealers will provide any service or adjustments which may be required to keep your unit operating at peak efficiency. Should engine servi

4 - 16NOTE: When temperature is below -15° F (-26° C) additional priming may be needed.6. Insert key into ignition switch on engine and push into RUN

4 - 174.6 PRE-STARTFrozen ImpellerIMPORTANT: Before starting engine, check impeller to be sure it is not frozen.To check impeller:1. With key in STOP

4 - 18Auger ShaftNOTE: To grease auger shaft, remove shear bolt nuts, and shear bolts. Turn auger on shaft while applying grease at zerk fittings. Rep

4 - 19Replace Attachment Drive BeltSee Figure 10.1. Place new belt onto lower pulley and while holding brake out of way, tip unit together.2. Secure b

21.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . 1-41.1 The Manual . . . . . . . . . . . . . . . . . . . . . . 1-41.2 Service and Re

4 - 204.11 SHEAR BOLTSIMPORTANT: Use only Ariens shear bolts for replacement. Use of any other type of shear bolt may result in severe damage to unit

5 - 215.1 DEFLECTOR REMOTE Deflector must stay in selected position while throwing snow.If deflector does not stay in set position: 1. Tighten nut be

5 - 225.3 RUNNERSRunners should be adjusted (Figure 14) as conditions require.1. Position unit on a hard, flat, smooth level surface. 2. Adjust runne

5 - 234. Check brake. a. When the clutch lever is disengaged, the brake must contact the attachment belt. b. When the clutch lever is engaged, the bra

5 - 245.6 SPEED SELECTOR ADJUSTMENTTo adjust (Figure 19):1. Remove hair pin from adjustment pivot pin.2. Pull shift rod and adjustment pivot pin out

6 - 256.1 LOWER HANDLEBAR1. Remove bolts attaching lower handlebar to each side of frame and remove lower handlebar.2. Check parts for wear or replac

6 - 261. Control Panel2. Speed Selector Lever3. Clutch Control4. Shift Rod5. Shift Pivot6. Traction Clutch Cable7. Torsion Spring8. Auger Clutch Cable

7 - 277.1 ENGINE TROUBLESHOOTINGThe following troubleshooting chart is to be used to isolate engine problems and give possible causes and corrective

7 - 28Excessive Fuel ConsumptionPoor compression Repair per instructions in manufacturer’s manualIncorrect grade of fuel Use fuel recommended in manuf

7 - 29See your engine manual for information on the operation and maintenance of your engine. Follow those instruc-tions for oil and filter changes.7.

3Ariens Company655 West Ryan StreetP.O. Box 157Brillion, Wisconsin 54110-0157 USATelephone (920) 756-2141Facsimile (920) 756-2407EC DECLARATION OF CO

8 - 308.1 WHEELS AND AXLEThe wheels are held onto the axle with locking pins (Figure 22). To remove a wheel pull the locking pin and the wheel will s

9 - 319.1 REMOVE FRICTION DISCSee Figure 23.1. Shut off engine, remove key, disconnect spark plug wire, and allow unit to cool completely.2. Place un

9 - 329.5 FRICTION PLATEThe friction plate can be removed and inspected when the drive system, friction plate, and axle have been removed. Refer to t

10 - 3310.1 AUGER/IMPELLER REMOVALPlace unit in the belt service position (Figure 5).1. Remove bolt holding auger driven pulley to shaft and remove p

10 - 3410.3 DISCHARGE CHUTETo remove discharge chute unbolt the chute positioning assembly from the discharge chute. Tip discharge chute forward and

10 - 3510.4 RUNNERSRunners should be adjusted as conditions require (Figure 28). Raising or lowering runners controls distance scraper blade is held

11 - 3611.1 ALUMINUM GEAR CASE1. Remove auger/impeller and gearcase from housing referring to Auger/Impeller Section.2. Remove eight bolts that hold

12 - 37SECTION 12 - TROUBLESHOOTINGProblem Probable Cause CorrectionEngine will not crank/start.1. Fuel tank is empty.2. Fuel shut-off valve closed.3.

12 - 38SERVICE PARTSOrder the following parts through your Dealer:Part No. Description00036800 Ariens Hi-Temp Grease (3, 3 oz. cartridges)21533400 Spa

Ariens Company655 West Ryan StreetP.O. Box 157Brillion, WI 54110-0157920-756-2141Fax 920-756-2407www.ariens.com

4CE Sound and Vibration – Niveau sonore et vibration CE – CE-Geräuschpegel und Vibrationswerte – Livello sonoro e vibrazioni CE – Sonido y vibración

51.1 THE MANUALThis manual provides complete instructions for service, maintenance, disassembly, repair, and installation of the mechanical componen

2 - 62.1 SAFETY ALERTSLook for these symbols to point out important safety precautions. They mean:Attention!Personal Safety Is Involved!Become Alert!

2 - 7DANGER!DANGER! WARNING!2.6 PREPARATIONBefore you start to remove any parts, proper preparation is very important for efficient work. A clean wor

2 - 8Complete a walk around inspection of unit and work area to understand: • Work area • Your unit • All safety decalsALWAYS check overhead and

2 - 9Before cleaning, removing clogs or making any inspections, repairs, etc.: disengage clutch(es), stop unit and engine, remove key, allow moving pa