Ariens 992807-ProZoom 60 Specifications Page 30

  • Download
  • Add to my manuals
  • Print
  • Page
    / 116
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 29
PROBLEM
Excessive Vibration
Uneven Cutting Height
Blades Wear Too Fast
Not Cutting Clean
Streaking or Windrow
Conditions in Cutting
Swath
Blades Won't Rotate
Mower Places Load
on Tractor
Excessive Mower
Deck Noise
PROBABLE CAUSE
1. Loose spindle/blade fasteners•
2. Blade interference with grass buildup in
deck.
3. Blades out of balance•
CORRECTION
1. Retorque or replace as necessary•
2. Clean the underside of the deck.
,
Blade(s) broken or worn badly• 4.
Engine mounting bolts are loose• 5.
Engine/Idler/Blade pulley loose• 6.
,
5.
6.
7. Engine pulley damaged• 7.
8. Failed spindle bearing• 8.
Blades dull. 1
Cutting blades bent. 2.
Deck not level• 3.
Anti-scalp not set correctly• 4.
,
2.
3.
4.
,
6.
5. Grass buildup under deck.
6. Incorrect tire pressure.
7. Blade spindle bent. 7.
8. Ground speed too fast. 8.
1. Cutting in sandy conditions. 1
2. Cutting in rocky conditions. 2.
3. Heat treat has been removed by 3.
sharpening with grinder•
1. Blades dull.
2. Blades installed upside down.
3. Blade RPM too slow.
4. Mower deck not level•
5. Mower tires mashing grass•
6. Ground speed too fast.
Excessive grass buildup under deck.
Blades dull. 1.
Blades installed upside down. 2.
Conditions too wet for mowing• 3.
Excessive grass buildup under deck. 4.
Ground speed to fast for conditions• 5.
Deck belt worn, loose or broken• 1.
Deck belt off pulley• 2.
Clutch failed• 3.
Engine RPM too low. 1.
Ground speed too fast. 2.
Excessive grass buildup under deck. 3.
Excessive grass buildup under deck. 1.
,
1.
2.
3.
4.
5.
1.
2.
3.
1.
2.
3.
1.
Balance blades• See Blade Maintenance
on page 27.
Replace blades in set of three•
Tighten the engine mounting bolts•
Tighten the pulley•
Contact Dealer•
Contact Dealer•
Sharpen or replace blades•
Install new blades•
Level deck.
Adjust height of anti-scalp wheel•
Clean underside of deck.
Adjust psi to 12 psi rear and 20 psi front•
Contact Dealer•
Lower ground speed•
Increase deck mowing height•
Increase deck mowing height•
Replace blades in sets of three•
1. Sharpen or replace blades.
2. Install blades correctly.
3. Use full throttle position.
4. Tires under inflated. See Tire and Wheel
Service on page 27.
5. Too wet or lush to mow. Reverse
directions an re-mow area.
6. Reduce ground speed.
7. Clean underside of deck.
Sharpen or replace blades.
Install blades correctly.
Allow grass to dry before mowing.
Clean underside of deck.
Reduce ground speed.
Replace deck belt.
Reinstall deck belt.
Contact dealer.
Use full-throttle position.
Reduce ground speed.
Clean underside of deck.
Clean underside of deck.
GB - 30
Page view 29
1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 115 116

Comments to this Manuals

No comments