Owner/Operator Manual Manuel du Propriétaire/UtilisateurModel911707 – Pro-24 HW Brush Cutter – CARBBrush Cutter04453400 1/12Printed in USAENGLISHFRENC
GB - 1012. Tighten hardware securing lower end of each handlebar support to frame to 23 lbf-ft (31 N•m). See Figure 7.Wheel Drive Link InstallationSee
GB - 11Engine Preparation1. Check engine oil level and add if necessary. See engine manual.2. Fill fuel tank. See FILLING FUEL TANK on page 13.3. Conn
GB - 12CONTROLS AND FEATURESSee Figure 10.PTO Clutch LeverPTO clutch control lever is used to release the blade pulley brake and engage the mower blad
GB - 13Engine ThrottleThe throttle lever controls the choke, engine speed and stops engine.(1) Choke (Gradually move lever to Slow position once engin
GB - 14Starting1. Check each item in the Before Each Use section of the MAINTENANCE SCHEDULE on page 15.2. Ensure the wheel drive is disengaged.3. Pla
GB - 15CHECK PTO CLUTCH LEVERThe blade must stop within 3 seconds after releasing this control lever. If the blade continues to run, adjust or repair
GB - 16Sharpening Mower Blades1. Remove mower blade from unit. See Remove Mower Blade on page 15.Discard mower blade if:• More than 1/2 in. (1.3 cm) o
GB - 17CHECK DRIVE BELTSCheck tension of mower blade and wheel drive belts. See BELT TENSION ADJUSTMENT on page 20. Check drive belts for wear and/or
GB - 186. Gently press against cable between control lever and adjuster. There must be a slight amount of deflection in cable with clutch disengaged.7
GB - 19Wheel Drive Speed AdjustmentSee Figures 14 and 15.Wheel drive speed is determined by how deep the wheel drive lower belt rides in the variable
GB - 2Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Assembly . . . . . . . . . . . . . . . . . . . . . . . . 8Controls and Features.
GB - 207. Tighten fine-adjustment knob to adjust drive roller gap at wheels to be 1/8 – 1/4" (3 – 6 mm).8. Install drive belt guards. See Drive B
GB - 213. Loosen flanged nut on each adjustment hex bolt.IMPORTANT: To avoid bending adjustment bolts, or have them slip off adjustment brackets, it m
GB - 225. Hold the flanged nyloc nut (on the inside of the engine mounting plate) stationary while turning the belt tensioning bolt clockwise to incre
GB - 23IMPORTANT: To avoid bending adjustment bolts, or have them slip off adjustment brackets, it may be necessary to pull back on wheel drive assemb
GB - 24Wheel Drive Upper Belt ReplacementSee Figure 22.1. Remove wheel drive lower belt. See Wheel Drive Lower Belt Replacement on page 22.2. Loosen t
GB - 25Mower Blade Drive Belt ReplacementSee Figure 23.1. Remove wheel drive lower belt. See Wheel Drive Lower Belt Replacement on page 22.2. Loosen t
GB - 26IMPORTANT: NEVER spray unit with high-pressure water or store unit outdoors. Store mower in a cool, dry, protected location.CleaningIMPORTANT:
GB - 27TROUBLESHOOTINGPROBLEM PROBABLE CAUSE CORRECTION Engine will not start1. Fuel tank empty or low.2. Spark plug wire loose or off.3. Engine throt
GB - 28TROUBLESHOOTINGPROBLEM PROBABLE CAUSE CORRECTION Wheel drive does not engage1. Wheel drive control not engaged.2. Wheel drive belts tension too
GB - 29SPECIFICATIONSModel Number 911707Description Pro-24 HW Brush Cutter – CARBLength – in. (cm) 68.5 (174)Height – in. (cm) 44.5 (113)Width – in. (
GB - 3PRODUCT REGISTRATIONThe Ariens dealer must register the product at the time of purchase. Registering the product will help the company process w
Commercial_201230Commercial Mowing Equipment Limited WarrantyAriens Company (Ariens) warrants to the original purchaser that Ariens, Gravely and Count
Commercial_201231Exceptions and LimitationsThe chart below details special exceptions to this warranty:Customer ResponsibilitiesRegister the product i
Commercial_201232DisclaimerAriens Company may from time to time change the design of its products. Nothing contained in this warranty shall be constru
CARB/EPA 201233 CALIFORNIA AND EPA (UNITED STATES ENVIRONMENTAL PROTECTION AGENCY) EVAPORATIVE EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS
CARB/EPA 201234(4.) Repair or replacement of any warranted part under the warranty provisions of this article must be performed at no charge to the ow
Ariens655 West Ryan StreetBrillion, WI 54110920-756-4688Fax 920-756-2407www.ariens.com
GB - 4SAFETY ALERTSLook for these symbols to point out important safety precautions. They mean:Attention!Personal Safety Is Involved!Become Alert! Obe
GB - 5SAFETY DECALS AND LOCATIONSALWAYS replace missing or damaged safety decals. Refer to for safety decal locations.1. DANGER! TO AVOID SERIOUS INJ
GB - 6DO NOT mow wet grass. ALWAYS be sure of your footing. Keep a firm hold on handlebar. Walk, NEVER run.Engine/blade control feature on mower stops
GB - 7This product is equipped with an internal combustion engine. DO NOT use on or near any unimproved, forest or brush covered land unless the exhau
GB - 8ALWAYS drain fuel outdoors away from ignition sources.ALWAYS shut off engine, and remove key, and close fuel shutoff valve when transporting uni
GB - 95. Remove and retain handlebar mounting hardware from each side of mower frame. See Figures 4 and 5.6. Place the lower hole of one side of the h
Comments to this Manuals