Owner/Operator ManualModels921001 – ST824E921002 – ST1027LE921003 – ST1130DLE921004 – ST924DLE Sno-Thro®00660400A 10/07Printed in USAENGLISHFRANÇAIS
GB - 10NOTE: Do not remove the pin installed on the chute rod.NOTE: To ensure the discharge chute follows its full range of travel, make sure the cont
GB - 11Install Discharge Chute and Discharge Chute Crank (921001)(Figure 12)1. Grease underside of discharge chute ring (if not already greased).2. Re
GB - 12Check Tire Pressure Check tire pressure and adjust to the pressure listed on tire sidewall.Check Auger Gearcase OilCheck oil level in auger gea
GB - 131. Attachment Clutch Lever2. Speed Selector3. Traction Drive Clutch Lever4. Chute Control5. Oil Fill/Dipstick6. Discharge Chute Deflector7. Dis
GB - 141. Attachment Clutch Lever2. Speed Selector3. Deflector Remote Control 4. Chute Control5. Traction Drive Clutch Lever6. Oil Fill/Dipstick7. Dis
GB - 15Controls AND FEATURESSee CONTROLS and FEATURES on page 13 for all Controls and Features locations.Dual Handle Interlock When Attachment Clutch
GB - 16IMPORTANT: DO NOT change motion from forward to reverse with clutch engaged. Forward speed can be changed without declutching.Choke Control Kno
GB - 17Discharge Chute Discharge chute rotates 200°.ALWAYS position discharge chute in safe direction and angle, away from operator and bystanders, be
GB - 18Axle Lock Pin (921001)(Figure 20) Use the axle lock pin to lock or unlock the right or left wheel. Lock both wheels to increase traction; unloc
GB - 195. Fill fuel tank to within 1/2 in. (1.2 cm) below bottom of filler neck with unleaded gasoline. NOTE: Tank capacity is 1 gallon (3.8 liters).6
GB - 2SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . 4ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . 8CONTROLS and FEATURES. . . .
GB - 207. Grasp starter handle and pull rope out slowly until it pulls harder. Let rope rewind slowly.8. Pull rope with a rapid continuous full arm st
GB - 21Ariens Dealers will provide any service or adjustments which may be required to keep your unit operating at peak efficiency. Should engine serv
GB - 22If clutches do not engage or disengage properly, adjust or repair before operation. See Attachment Clutch/Brake Adjustment on page 27 and Trac
GB - 23General LubricationIMPORTANT: Wipe each fitting clean before and after lubrication. Do not wipe gearcase filler plug; wiping the gearcase fille
GB - 24Scraper BladeIMPORTANT: Damage to auger/impeller housing will result if blade wears down too far.Scraper blade is adjustable to compensate for
GB - 255. Check function of remote wheel lock. If wheel lock does not function properly, remove bottom cover to check cable slack.6. Repeat steps 2 –
GB - 26If chute does not rotate freely:Tighten the cable by loosening the upper adjustment nut, and then tightening the lower adjustment nut against t
GB - 27Speed Selector AdjustmentTo adjust (Figure 33):1. Disconnect adjustment pivot pin from speed selector lever by removing hair pin.2. Place the s
GB - 283. With the attachment clutch disengaged, check that the attachment idler arm lightly touches the frame. See Figure 35.4. Tighten jam nut on th
GB - 292. Adjust attachment idler position. See Figure 38.a. Loosen idler adjustment nut.b. To increase spring extension, move idler closer to belts a
GB - 3• Record Unit Model and Serial numbers here.• Record Engine Model and Serial number here.Product RegistrationThe Ariens dealer must register the
GB - 302. If there is less than 1/16 in. (1.6 mm) gap between brake pad and belts, follow these steps:a. To increase brake pad gap, loosen idler adjus
GB - 314. To adjust traction clutch (Figure 42):a. With the traction drive clutch lever disengaged, loosen the jam nut on the cable adjuster.b. Turn t
GB - 32IMPORTANT: If traction clutch cannot be adjusted within specified range, see your Dealer for repairs.Attachment Drive Belt ReplacementRemove ol
GB - 335. Check adjustment. See Attachment Clutch/Brake Adjustment on page 276. Reconnect chute crank and secure with spring clip. Reconnect chute lo
GB - 34Friction Disc Replacement1. Shut off engine, remove key, disconnect spark plug wire and allow unit to cool completely.2. Place unit into servic
GB - 35Short TermIMPORTANT: NEVER spray unit with high pressure water or store unit outdoors.Run with attachment clutch engaged a few minutes after ea
GB - 36TROUBLESHOOTINGPROBLEM PROBABLE CAUSE CORRECTION Engine will not crank/start.1. Fuel tank is empty.2. Fuel shut-off valve closed.3. Build up of
GB - 37SPECIFICATIONSModel Number 921001 921002 921003 921004DescriptionST824E ST1027LE ST1130DLE ST924DLEEngine - TecumsehLH318SATecumsehLH358SATecu
Ariens Company • 655 W. Ryan St, • Brillion, WI 54110-1072 • (920) 756-2141 • www.ariens.comALW2-62905Ariens Limited Warranties2-Year Limited Lawn a
Ariens Company • 655 W. Ryan St. • Brillion, WI 54110-1072• (920) 756-2141 • www.ariens.comALW2-62905Exceptions, Limitations, ExclusionsThese warranti
GB - 4Safety AlertsLook for these symbols to point out important safety precautions. They mean:Attention! Personal Safety Is Involved!Become Alert!
Ariens Company655 West Ryan StreetBrillion, WI 54110-1072920-756-2141Fax 920-756-2407www.ariens.com
GB - 51. WARNING!2. DANGER! 3. DANGER!Safety RulesRead, understand, and follow all safety practices in Owner/Operator Manual before beginning assembly
GB - 6Keep children and people away. Keep children out of work area and under watchful care of a responsible adult.NEVER allow children to operate or
GB - 7Before cleaning, removing clogs or making any inspections, repairs, etc.: disengage clutch(es), stop unit and engine, remove key, allow moving p
GB - 8Package ContentsAssemblyTools Required:•Pliers• Open-End Wrenches: 3/8, 7/16, 1/2, 9/16 in. and/or Adjustable Wrench• Tire GaugeUnfold Handlebar
GB - 9..Install Discharge Chute and Discharge Chute Crank (921002, 003, 004)(Figure 8)1. Grease underside of discharge chute ring (if not already grea
Comments to this Manuals