Owner/Operator ManualModels932105 - 8526932506 - 8526Sno-Thro®00295900A 12/04Supersedes 00295900Printed in USAENGLISHFRANÇAISESPAÑOLTransfer model &am
GB - 10Install Discharge Chute Figure 5.1. Grease underside of discharge chute ring (if not already greased).2. Remove mounting hardware from auger ho
GB - 11Deflector Remote 1. Remove e-ring and flat washer from stud on discharge chute.2. Route deflector remote cable between the engine and the chute
GB - 12Run-in Attachment Belt1. Start unit in a well-ventilated area according to Starting and Shut-Off in Operation.2. Engage attachment clutch lever
GB - 13CONTROLS AND FEATURESSee Figure 8 for all Controls and Features locations.Dual Handle Interlock When Attachment Clutch and then Traction Drive
GB - 14ThrottleThe throttle controls the engine speed. To increase or decrease the engine speed, adjust to:1. Fast (normal or warm starts)2. Part-Th
GB - 15Scraper BladeThe scraper blade allows the back of the housing to keep better contact with the surface being cleared. It also prevents damage to
GB - 163. Check Dual Handle InterlockWithout the engine running, press down (engage) both clutch levers. Release attachment clutch lever. Attachment c
GB - 179. Press starter button on engine until engine starts.IMPORTANT: DO NOT operate starter more than 15 seconds per minute, as overheating and dam
GB - 18 * After first two hours of operation.CHECK DUAL HANDLE INTERLOCK Without the engine running, press down (engage) both clutch levers. Release a
GB - 19GENERAL LUBRICATIONIMPORTANT: Wipe each fitting clean before and after lubrication.IMPORTANT: DO NOT allow grease or oil to get on friction dis
2Ariens Company655 West Ryan StreetP.O. Box 157Brillion, Wisconsin 54110-0157 USATelephone (920) 756-2141Facsimile (920) 756-2407EC DECLARATION OF CON
GB - 20DISCHARGE CHUTEIf chute does not stay in position while operating, tighten nut on carriage bolt at pivot point to increase tension on spring (F
GB - 21SCRAPER BLADEIMPORTANT: Damage to auger/impeller housing will result if blade wears down too far.Scraper blade is adjustable to compensate for
GB - 225. Thread the adjustment pivot pin along the shift rod until it aligns with the mating hole on the speed selector lever.6. Reinsert the pivot p
GB - 236. Adjust clutch per Attachment Clutch/Brake Adjustment below.7. Replace chute crank and secure with spring pin. 8. Replace belt cover and secu
GB - 24d.If spring does not stretch at least 3/16 in. (4.7 mm), or the belt tension is insufficient to throw snow properly, remove the attachment belt
GB - 252. Turn the adjustment barrel up the cable to decrease the distance between clutch lever and handlebar.Turn the adjustment barrel down the cabl
GB - 265. Bolt new friction disc to shift carrier. Tighten hardware to 5-6 lbf-ft (6.8 to 8.13 N•m).6. Install roll pins in hex shaft. Ensure roll pin
GB - 27 TROUBLESHOOTINGPROBLEM PROBABLE CAUSE CORRECTION Engine will not crank/start.1. Fuel tank is empty.2. Fuel shut-off valve closed.3. Build up o
GB - 28 SPECIFICATIONSModel Number 932506 932105Description 8526 8526Engine - Tecumseh LH318SA LH318SA Power Max - HP (Kw/min-1)8.5 (6.3) Fast Idle Sp
GB - 293-Year Limited Sno-Thro WarrantyAriens Company warrants to the original purchaser that consumer products manufacturedby Ariens Company will be
3CE Sound and Vibration – Niveau sonore et vibration CE – CE-Geräuschpegel und Vibrationswerte – Livello sonoro e vibrazioni CE – Sonido y vibración C
Ariens Company655 West Ryan StreetP.O. Box 157Brillion, WI 54110-0157920-756-2141Fax 920-756-2407www.ariens.com
GB - 4Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . 9Controls and
GB - 5DISCLAIMERAriens reserves the right to discontinue, make changes to, and add improvements upon its products at any time without public notice or
GB - 6REQUIRED OPERATOR TRAININGOriginal purchaser of this unit was instructed by the seller on safe and proper operation. If unit is to be used by so
GB - 7ALWAYS remove key and/or wire from spark plug before assembly, maintenance or service. Unintentional engine start up can cause death or serious
GB - 8DO NOT overload the machine capacity by attempting to clear snow at too fast a rate.DO NOT operate at too fast a rate.Slow down and turn corners
GB - 9Keep all hardware properly tightened. Check shear bolts frequently. Maintain or replace safety and instruction labels, as necessary.NEVER store
Comments to this Manuals