Ariens SNO-THRO 924326-ST1336LE Specifications

3 - 10Model Number 924101 924102 924103 924104 924105Model ST 928 ST 1032 ST 1236 ST 1028 STT8Engine - Manufacturer TecumsehHMSK90Te c u m s e hHMSK10

3 - 11Model Number 924106 924311 924312 924313 924314Model ST 1024 ST 824 ST 924 LE ST 1028 L ST 1228 LEEngine - Manufacturer TecumsehHSMK100Te c u m

3 - 12Model Number 924315 924316 924317 924318 924319Model ST 1232 LE ST 1236 LE ST 928 LE ST 824 ST 924 LEEngine - Manufacturer TecumsehOHSK120Te c u

3 - 13Model Number 924320 924321 924323 924324 924325Model ST 1232 LE ST 1236 LE ST 1024 SHO ST 1128 LE ST 1132 LEEngine - Manufacturer TecumsehOHSK12

3 - 14Model Number 924326 92410700Model ST 1336 LE ST 1336 LEEngine - Manufacturer TecumsehOHSK130Te c u m s e hOHSK130Fuel Unleaded UnleadedFuel Tank

4 - 154.1 CONTROLS AND FEATURESSECTION 4 - GENERAL MAINTENANCE & ADJUSTMENTS1. Attachment Clutch Lever2. Speed Selector3. Chute Crank4. Wheel Dri

4 - 164.2 SERVICE POSITIONSAriens Dealers will provide any service or adjustments which may be required to keep your unit operating at peak efficienc

4 - 17To add fuel to the fuel tank:1. Refuel the unit only in a well ventilated, open area.2. Stop the engine and allow to cool.3. Clean the fuel cap

4 - 184.6 AUGER GEARCASEIMPORTANT: Too much lubricant may cause excessive leakage. Too little lubricant will cause gear and/or bearing damage. Proper

4 - 19IMPORTANT: Use care when rotating the belt fingers to prevent deformation of parts.NOTE: To gain clearance engage traction clutch and if necessa

2Section 1 - Introduction . . . . . . . . . . . . . . . . . 1.31.1 The Manual . . . . . . . . . . . . . . . . . . . . . . . 1.31.2 Service and Rep

4 - 20For Replacement:1. Slide auger outward against roll pin and align hole in shaft with hole in auger. The holes in the shaft for the roll pins and

4 - 21Attachment Clutch/Impeller BrakeTo adjust Attachment Clutch/Impeller Brake:1. Remove belt cover. When clutch is disengaged there should be a sli

4 - 22Speed SelectorTo adjust the speed selection linkage:1. TIp unit forward onto auger housing.2. Put speed selector into reverse.3. At the speed se

5 - 235.1 UPPER HANDLEBAR PANEL & KEY SWITCHDisconnect wires to key switch.Remove key switch nut and remove key switch from upper handlebar panel

5 - 245.6 CLUTCH YOKE AND FORKRemove locknut and adapter spacer holding spring assembly in clutch yoke (Figure 13).Remove capscrew, nut, and rod adap

6 - 256.1 ENGINE TROUBLESHOOTINGThe following troubleshooting chart is to be used to isolate engine problems and give possible causes and corrective

6 - 26See your engine manual for information on the opera-tion and maintenance of your engine. Follow those instructions for oil and filter changes.6.

7 - 277.1 DIFFERENTIAL, LOCKOUT, AND AXLEPlace unit in Upright Service Position.1. Remove groove pin that secures lockout assembly to left hand axle

7 - 287.5 HEX SHAFTPlace unit in Upright Service Position.1. Hold hex shaft on sprocket end with a wrench and remove lock nut at outside of frame. 2.

8 - 298.1 FRICTION WHEEL1. To replace friction wheel, tip unit up into the upright service position.2. Remove bottom cover by removing four cap screw

1 - 31.1 THE MANUALIt is the purpose of this manual to provide complete instructions for service, maintenance, disassembly, repair, and installation

8 - 301. Spindle Hub2. Friction Disk3. Disc Hub4. Flange Bushing5. Sleeve Bushing6. Ball Bearing7. Drive Plate8. Spindle9. Housing Mount10.Bearing11.B

9 - 319.1 AUGER/IMPELLER REMOVALPlace unit in the Belt Service Position.1. Remove three nuts holding pulley to hub and remove pulley and key.2. Loose

9 - 329.4 DISCHARGE CHUTERemove mounting clips from discharge chute, oil and position chute on auger/impeller housing. Secure discharge chute with mo

9 - 331. Chute Deflector2. Wave Washer3. Control Cable4. Discharge Chute5. Chute Clamp6. RunnerFigure 19123456

10 - 3410.1 CAST IRON GEAR CASE (WORM GEAR)Remove auger/impeller and gear case from housing referring to Auger/Impeller Section.Remove four bolts fro

10 - 35Figure 20PS04721. Impeller2. Worm Shaft3. Adjustment Plug4. Worm and Gear Service Assembly5. Rake Shaft6. Gear Case Shaft7. Gear CaseCast Iron

10 - 36Figure 21PS02811. Impeller2. Worm Shaft and Gear Assembly3. Thrush Collar4. Case, Left Side, Large Bore5. Case, Right Side, Small Bore6. Rake S

Ariens Company655 West Ryan StreetP.O. Box 157Brillion, WI 54110-0157920-756-2141Fax 920-756-2407www.ariens.com

2 - 42.1 SAFETY ALERTSLook for these symbols to point out important safety precautions. They mean:Attention! Personal Safety Is Involved!Become Ale

2 - 52.9 SAFETY RULES Walk Around InspectionComplete a walk around inspection of unit and work area to understand:• Work area. • Your unit. • All saf

2 - 6Before maintenance, adjustments, or service (except where specifically recommended), shut off engine.Allow hot parts to cool.Keep unit free of di

3 - 7SECTION 3 - SPECIFICATIONSModel Number 924080 924081 924082 924083 924084Model ST T8 ST 824S ST 824 ST 828 ST 1032Engine - Manufacturer TecumsehH

3 - 8Model Number 924085 924086 924087 924088 924089Model ST 1236 ST 1028 ST 1232E ST 1028 E ST 824EEngine - Manufacturer Tecumseh OHSK 120TecumsehHMS

3 - 9Model Number 924090 924091 924092 924093 924100Model ST 0036 ST 1228E ST 1236E ST 924 ST 824DLEngine - Manufacturer TecumsehOHSK120Te c u m s e h