Owner/Operator ManualManuel Du Propriétaire/UtilisateurModels920400 – Sno-Tek 24920401 – Sno-Tek 26Sno-Tek™03883300A 8/09Printed in USAENGLISHFRANÇAIS
GB - 10Check Function of Dual Handle InterlockWithout the engine running, press down (engage) both clutch levers. Release attachment clutch lever. Att
GB - 111. Attachment Clutch Lever2. Speed Selector3. Traction Drive Clutch Lever4. Chute Crank 5. Muffler Guard6. Discharge Chute Deflector7. Discharg
GB - 12CONTROLS AND FEATURESSee Figure 7 for all Controls and Features locations.Dual Handle Interlock When attachment clutch and then traction drive
GB - 13Forward:(6) Fastest(1) SlowestReverse: (1) Slow(2) FastIMPORTANT: DO NOT change motion from forward to reverse with clutch engaged. Forward spe
GB - 14Discharge Chute CrankIMPORTANT: If chute does not stay in set position, adjust as directed in SERVICE AND ADJUSTMENTS on page 18, or repair be
GB - 153. Clean fuel cap and surrounding area to prevent dirt from entering fuel tank. 4. Remove cap.IMPORTANT: See engine manual for correct type and
GB - 169. Repeat steps 7 and 8 until engine starts. (If engine does not start, refer to TROUBLESHOOTING on page 28.)10. Adjust choke as needed.Shut Of
GB - 17MAINTENANCE SCHEDULEThe chart below shows the recommended maintenance schedule that should be performed on a regular basis. More frequent servi
GB - 18To ensure adequate lubricant level:1. Remove filler plug (Figure 12). Lubricant must be at least up to bottom of lubricant filler hole with uni
GB - 192. Adjust skid shoes by inserting a spacer of desired thickness under center of scraper blade, loosen skid shoe hardware, slide skid shoes to f
GB - 2SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . 4ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . 8CONTROLS and FEATURES. . . .
GB - 20DISCHARGE CHUTEIf discharge chute does not stay in position while operating, tighten nut on carriage bolt at pivot point to increase tension on
GB - 214. Remove belt finger by removing cap screws mounting belt finger to engine (Figure 20 or Figure 21).5. Remove attachment drive belt from engin
GB - 22TRACTION DRIVE BELT REPLACEMENTNOTE: Housing and frame must be tipped apart and attachment drive belt removed from engine sheave in order to ch
GB - 23ATTACHMENT CLUTCH/BRAKE ADJUSTMENTRemove Attachment Cable Slack1. Remove the belt cover.2. Loosen jam nut on cable adjustment barrel, and then
GB - 24Adjust the Attachment Clutch Cable Spring Extension1. Check the attachment clutch cable spring extension. Measure the length of the attachment
GB - 25Check Belt Finger Clearance (Figure 29)1. With clutch lever engaged, the belt finger located opposite the belt idler must be less than 1/8 in.
GB - 26FRICTION DISC REPLACEMENTRemove Friction Disc (Figure 31 and Figure 32):1. Shut off engine, remove key, disconnect spark plug wire and allow un
GB - 2713. Insert new friction disc assembly into frame. Install washers onto carrier bearing and slide into speed selector arm. 14. Slide hex shaft t
GB - 28TROUBLESHOOTINGPROBLEM PROBABLE CAUSE CORRECTION Engine will not crank/start.1. Fuel tank is empty.2. Fuel shut-off valve closed.3. Build up of
GB - 29SPECIFICATIONSModel Number 920400 920401Description Sno-Tek 24 Sno-Tek 26Engine LCT Storm Force LCT Storm ForceGross Torque* - ft-lbs (N-m) 9.
GB - 3• Record unit model and serial numbers here.• Record engine model and serial numbers here.PRODUCT REGISTRATIONThe Ariens dealer must register th
ARIENS COMPANYGRAVELY® | STENS® | LOCKE® | NATIONAL® MOWER | BYNORM® | EVERRIDE® | GREAT DANE® Sno-Tek_200930 of 31Sno-Tek™ Two-Year Limited WarrantyA
ARIENS COMPANYGRAVELY® | STENS® | LOCKE® | NATIONAL® | BYNORM® | EVERRIDE® | GREAT DANE® Sno-Tek_200931 of 31 Exclusions – Items Not Covered by This
Ariens Company655 West Ryan StreetBrillion, WI 54110-1072920-756-2141www.ariens.com
GB - 4SAFETY ALERTSLook for these symbols to point out important safety precautions. They mean:Attention! Personal Safety Is Involved!Become Alert!
GB - 51. WARNING!2. DANGER! 3. DANGER!SAFETY RULESRead, understand, and follow all safety practices in owner/operator manual before beginning assembly
GB - 6DO NOT operate near drop-offs, ditches, or embankments. Unit can suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an ed
GB - 7Check clutch and brake operation frequently. Adjust and service as required. All motion of drive wheels and auger/impeller must stop quickly whe
GB - 8PACKAGE CONTENTSASSEMBLYTools Required:• Pliers• Open-end wrenches: 3/8, 7/16, 1/2, 9/16 in. and/or adjustable wrench• Tire gaugeUnfold Handleba
GB - 9Install Discharge Chute (Figure 5)1. Remove mounting hardware from the bottom of the chute pedestal.2. Install discharge chute over opening in t
Comments to this Manuals