Quick Start Guide Deluxe 30 (921013 s/n 75000 & up) • Step 1: Assemble Handlebars • Step 2: Connect Headlight Wire Harness • Step 3: Install Trigg
Step Six: Install Remote Deflector Control Cable NOTE: Connect the barrel cable end to the chute deflector cable anchor before clipping the cable to
Step Seven: Install Skid Shoes 1. Remove hardware from skid shoes. 2. Install hardware through blower housing and skid shoe as shown. 3. Adjust skid
Step Eight: Check Function of Dual Handle Interlock Without the engine running, press down (engage) both clutch levers. Release attachment clutch leve
Step Nine: Check Tire Pressure Check tire pressure and adjust to the pressure listed on tire sidewall.
Check oil level in auger gearcase (see Check Auger Gearcase in Owners Manual). Step Ten: Check Auger Gearcase Oil
IMPORTANT: The engine is shipped with oil in crankcase. Refer to Engine Manual for detailed instructions. Step Eleven: Check Engine Crankcase Oil
Fill fuel tank. DO NOT OVERFILL! See FILLING FUEL TANK in Owners Manual. Remove the plug from the fuel tank and install the fuel cap located in the a
Step Thirteen: Starting the Engine
Starting Engine / Step A: Throttle Move the throttle control lever to the fast position. Operate the engine with the throttle control lever in the fas
Starting Engine / Step B: Fuel Valve Turn the fuel shut-off valve to the ON position.
Step One: Assemble Handlebars (Unfold Lower Handlebar) IMPORTANT: Be sure to block wheels or secure unit so it does not move during assembly. 1. Rotat
Starting Engine / Step C: Key Insert the key and turn to the ON/START position.
Starting Engine / Step D: Choke Turn the choke control knob to the choke position. NOTE: Choke is usually unnecessary when restarting a warm engine.
Starting Engine / Step E: Prime Push the primer two times. Be sure to cover vent hole on primer bulb. NOTE: Priming is usually unnecessary when res
Starting Engine / Step F: (Manual Start) Firmly hold the starter cord handle. Pull the starter cord handle slowly until resistance is felt, then pull
Starting Engine / Step F: (Electric Start) First connect the extension cord to the power cord receptacle and then into a wall receptacle. I
Starting Engine / Step G: (Electric Start) Depress the push button. After you start the engine, first disconnect the extension cord from the wall rece
Starting Engine / Step H: Warm up Allow the engine to warm up for several minutes. Then, slowly move the choke control knob to the RUN position.
Step Fourteen: Stopping the Engine Turn the key to the off position or move throttle control lever to slow and then to the stop position (completely l
Additional Resources • Refer to Owners Manual and Engine Manual • Contact Ariens Company www.ariens.com Phone: 920-756-4688 E-mail: [email protected] •
Step One: Assemble Handlebars (Attach Upper Handlebar Assembly) 1. Attach upper handlebar assembly to lower handlebar using two sets of the handlebar
Step One: Assemble Handlebars (Attach Control Cables) 1. Hook Spring end of attachment control cable to the clutch arm. 2. Hook spring end of the trac
Step One: Assemble Handlebars (Unfold Upper Handlebar) Assembly) 1. Rotate handlebar into operating position. NOTE: Be careful not to damage cable spr
Step Two: Connect Headlight Wire Harness NOTE: The headlight wire harness comes attached to the upper handlebar assembly. 1. Route the wire harness al
Step Three: Install Trigger Cable NOTE: Trigger cable assembly comes attached to the Sno-thro unit. 1. Attach remote trigger cable assembly to upper h
Step Four: Install Discharge Chute 1. Grease underside of discharge chute ring (if not already greased). 2. Remove mounting hardware from auger housin
Step Five: Install Discharge Chute Crank 1. Remove the gear cover from top of chute pedestal. 2. Insert the short end of the chute crank into the hole
Comments to this Manuals