Ariens 920013 Specifications download pdf (Page 18)

GB - 18

If clutches do not engage or disengage

properly, adjust or repair before operation

(see Attachment Clutch/Brake Adjustment on

page 25 and Attachment Drive Belt

Replacement on page 27).

4. Check Axle Lock Pins

Use the axle lock pins to lock or unlock the

wheels. Lock both wheels to increase

traction; unlock one wheel to allow for easier

turning of the unit.

5. Check Skid Shoes

Check and adjust skid shoes (Skid Shoes on

page 23). Allow 1/8 in. (3 mm) between

scraper blade and hard, smooth surface(s).

Allow 7/8 in. (22 mm) between scraper blade

and uneven or gravel surfaces.

6. Check Engine Fuel &

Crankcase Oil

Check and add fuel if required. Check that

the engine crankcase oil is full using dipstick.

Refer to Engine Manual for detailed

instructions.

TO STOP IN AN EMERGENCY

Immediately release both control levers to

stop unit in an emergency. Stop engine,

remove key and wait for all rotating parts to

stop before leaving operator’s position.

STARTING AND SHUT OFF

IMPORTANT: Allow unit and engine to adjust

to the outdoor temperature before clearing

snow. Before shut-off, run the attachment a

few minutes to prevent impeller freeze-up.

NOTE: Try out each control without the

engine running to see how it works and what

it does.

Manual Start

1. Turn discharge chute straight ahead.

2. Make sure that the traction clutch and

attachment drive clutch levers are fully

disengaged.

3. Push Primer Bulb 2 or 3 times for cold

engine.

NOTE: When temperature is below -15° F

(-26° C) additional priming may be needed.

4. If engine is cold, apply choke. See

Engine Manual for detailed instructions.

NOTE: A warm engine requires less choking

than a cold engine.

5. 920014 - Set throttle to proper starting

position.

920013 - Toggle ignition switch to "Run".

6. 920014 - Insert key into ignition and

rotate to run position.

920013 - Insert key into ignition switch

and push into RUN position. DO NOT

twist key after it is inserted.

7. Grasp starter handle and pull rope out

slowly until it pulls harder. Let rope

rewind slowly.

8. Pull rope with a rapid continuous full arm

stroke. Let rope rewind slowly.

IMPORTANT: DO NOT let Starter Handle

snap against Starter.

9. Repeat steps 7 and 8 until engine starts.

(If engine does not start, refer to

TROUBLESHOOTING on page 31.)

10. Adjust choke as needed.

11. 920014 - Set throttle to Part Throttle or

Slow position for adaptation to outside

temperature or travel. Set throttle to Fast

position for normal operation.

Electric Start (120V)

1. Connect extension cord to starter.

IMPORTANT: Prevent damage to unit. Know

voltage of your starter and only use matching

outlets.

2. Plug extension cord into 120V 3-wire,

grounded outlet.

IMPORTANT: Use only Ariens extension cord

(P/N 02483100) or an equivalent cord that is

rated for a minimum of 13 amps, grounded,

UL listed, CSA certified and labeled as

suitable for outdoor use.

3. Turn discharge chute straight ahead.

4. Make sure that the traction clutch and

attachment drive clutch levers are fully

disengaged.

5. Push Primer Bulb 2 or 3 times for cold

engine.

NOTE: When temperature is below -15° F

(-26° C) additional priming may be needed.

6. 920014 - Set throttle to proper starting

position.

920013 - Toggle ignition switch to "Run".

7. 920014 - Insert key into ignition and

rotate to run position.

920013 - Insert key into ignition switch

and push into RUN position. DO NOT

twist key after it is inserted.

WARNING: AVOID INJURY. Read

and understand the entire Safety

section before proceeding.

WARNING: FAILURE TO FOLLOW

INSTRUCTIONS could result in

personal injury and/or damage to

unit. DO NOT attempt to start your

unit at this time. Read entire

Owner/Operator Manual and the

Engine Manual first.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 39 40

Comments to this Manuals

No comments

Ariens 920013 Specifications Page 18

Comments to this Manuals

Related products and manuals for Garden tools Ariens 920013