Ariens 991800-ProZoom 2352S Specifications Page 31

  • Download
  • Add to my manuals
  • Print
  • Page
    / 64
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 30
GB - 31
Not Cutting Clean 1. Blades dull.
2. Blades installed upside down.
3. Blade RPM too slow.
4. Mower deck not level.
5. Mower tires mashing grass.
6. Ground speed too fast.
7. Excessive grass buildup under deck.
1. Sharpen or replace blades.
2. Install blades correctly.
3. Use full throttle position.
4. See Tire and Wheel Service on page 27.
Tires under inflated.
5. Too wet or lush to mow. Reverse
directions an re-mow area.
6. Reduce ground speed.
7. Clean underside of deck.
Streaking or Windrow
Conditions in Cutting
Swath
1. Blades dull.
2. Blades installed upside down.
3. Conditions too wet for mowing.
4. Excessive grass buildup under deck.
5. Ground speed to fast for conditions.
1. Sharpen or replace blades.
2. Install blades correctly.
3. Allow grass to dry before mowing.
4. Clean underside of deck.
5. Reduce ground speed.
Blades Won’t Rotate 1. Deck belt worn, loose or broken.
2. Deck belt off pulley.
3. Clutch failed.
1. Replace deck belt.
2. Reinstall deck belt.
3. Contact dealer.
Mower Places Load
on Tractor
1. Engine RPM too low.
2. Ground speed too fast.
3. Excessive grass buildup under deck.
1. Use full-throttle position.
2. Reduce ground speed.
3. Clean underside of deck.
Excessive Mower
Deck Noise
1. Excessive grass buildup under deck. 1. Clean underside of deck.
Engine Idling Poorly 1. Carburetor incorrectly adjusted.
2. Improper spark plug gap.
1. Contact Dealer.
2. Check and regap spark plugs.
Engine Backfires 1. Carburetor adjusted incorrectly. 1. Contact Dealer.
Engine Runs But Unit
Won’t Move
1. Drive belt loose or broken.
2. Hydraulic reservoir oil low.
3. Pump bypass valve open.
4. Hydraulic oil filter plugged.
5. Bad pump or motor.
1. Tighten or replace drive belt.
2. Refill reservoir.
3. Close bypass valve.
4. Replace hydraulic oil filter.
5. Contact Dealer.
Unit Loses Power or
Hydraulic System
Overheats
1. Hydraulic oil reserve too low.
2. Hydraulic oil reservoir out of cap.
1. Refill reservoir.
2. Overfill or water contaminated.
Loss of Power or
System Will Not
Operate in Either
Direction
1. Restrictions in air cleaner.
2. Poor compression.
3. Steering linkage needs adjustment.
4. Hydraulic bypass valve open.
5. Pump belt broken or worn.
6. Pump belt off of pulley.
1. Service air cleaner.
2. Contact Dealer.
3. Contact Dealer.
4. Close bypass valve.
5. Replace belt.
6. Reinstall belt on pulley.
Engine Overheats 1. Air intake screen clogged.
2. Cooling fins clogged.
1. Service air intake screen.
2. Clean fins.
Engine Stalling While
Blades Engaged
1. Operator not in seat.
2. Faulty safety system.
3. Spindle bearing failure.
4. Blades locked by foreign matter.
1. Sit on seat.
2. Contact Dealer.
3. Contact Dealer.
4. Clean underside of deck.
TROUBLESHOOTING
PROBLEM PROBABLE CAUSE CORRECTION
Page view 30
1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 63 64

Comments to this Manuals

No comments