Ariens 935000 User Manual download pdf (Page 11)

The Traction Drive Belt is easily replaced by lifting the

rear deck; loosening the belt fingers; including belt

finger on Traction Clutch Idler Arm; depressing the

Clutch Pedal and removing the belt. Replacement is

similar, depress the Clutch Pedal; install the belt and

replace the belt fingers. Adjust the three belt fingers to

provide Vi to Vie inch clearance from the belt with

clutch engaged (pedal up).

MOWER BELT - FIGURES 13 & 14

If belt squeals when Implement Power Clutch is proper

ly engaged, check adjustment of belt. If squeals con

tinue, belt may require replacement.

A. Removal

1. Place the Attachment Lift Lever in the lowest

position, (forward). Disengage the Attach

ment Clutch (lever to rear).

REPUCEMENT OF TRACTION DRIVE BELT • FIGURE 12

strength and stability. This assures that the belts will

deliver maximum performance and durability for each

product's specific applications.

The selling price of ARIENS BELTS reflects these quali

ty features. Our name and number stamped on your

replacement belt is your assurance of receiving the

quality you are paying for.

TOP VIEW

P.T.O.

31755 BELT FINGERS

ATTACHMENT IDLER ICLUTCHINQI

MOWER SHEAVE

P.T.O. SHEAVE

FIGURE 14

BELT CLEARANCE:

MAX. IN HIGHEST

POSITION; 1" MIN. IN

LOWEST POSITION.

MOWER BELT

2. Loosen the belt fingers at the PTO Sheave

and turn them away from the sheave.

3. Remove the hair pin or cotter pin securing

the brake band and rotate the band away

from the sheave. See Figure 13.

HAIR PIN

32" MOWER

ONLY

ADJUST FOR 1-1/8"

SPRING LENGTH

MOWER SHEAVE

38" MOWER ONLY

- HAIRPIN FIGURE 13

4. Raise the mower pan to its mid position and

remove the Mower Belt from the PTO

Sheave; lower the pan and remove the belt

from mower pan. See Figure 14.

B. Replacement

1. Position the replacement Mower Belt around

the sheave on the mower pan. Reposition

the brake band around the sheave and

secure with the cotter or hair pin. See Figure

13.

2. Raise the mower pan to its center position

and install the Mower Belt around the PTO

Sheave. See Figure 14.

A NOTE ABOUT ARIENS BELTS

ARIENS BELTS are individually engineered to the

highest standards of material quality, design, and con

struction including special cording locations for

MOWER BRAKE ADJUSTMENT - FIGURE 13

With the Mower Belt adjusted and the Implement

Power Clutch disengaged, adjust the nut on the end of

the brake rod until the spring is 1 Vs" in length. See

FIgur« 13.

MOWER RUNNER ADJUSTMENT

After adjusting the cutting height and blade pitch as

described elsewhere In this section, thè mower runners

may be adjusted, as desired, to allow smooth, even

cutting of grass at different cutting height settings. Ad

justment must be even from side to side. Assemble out

side spacers to runners and mower before center

spacers. This will aid in alignment and ease of installa

tion. Do not tighten hardware until outside spacers are

installed.

1. To pre-set the runners prior to a test cutting they

may be adjusted as shown in Figure 1 5.

SPACER

CARRIAGE BOL^

6071 SP

FIGURE 15

2. To obtain smoothest cutting in lowest cutting

height settings, the runners may be adjusted as

shown in Figure 1 6.

2 SPACERS 2 SPACERS

6071 SPACERS

FIGURE 16

To obtain smoothest cutting in higher cutting

height settings, the runners should be adjusted as

shown in Figure 1 7.

-NO SPACERS-Tc-

2 SPACERS

'6071 SPACER

Flfsi"-

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 39 40

Comments to this Manuals

No comments

Ariens 935000 User Manual Page 11

Comments to this Manuals

Related products and manuals for Gardening equipment Ariens 935000