Ariens SNO-THRO 924333 - 1024 User Manual download pdf (Page 12)

GB - 12

Electric Starter

The Electric Starter will start a properly choked and

cranked engine when the key is turned (12V) or start

button (120V) is pushed. Refer to Starting and

Shut-Off.

Recoil Starter Handle

When pulled, handle will turn engine over.

Discharge Chute Deﬂector

ALWAYS position Discharge Chute Deﬂector at safe

angle before starting engine.

Push Deﬂector handle forward or down to throw snow

lower. Pull Deﬂector Handle up or to the rear to throw

snow higher.

IMPORTANT: If Chute Deﬂector does not stay in set

position, adjust as directed in Service and

Adjustments, or repair before operation.

Deﬂector Remote (119,502,503)

Place Deﬂector into position before operation. DO NOT

throw snow any higher than necessary.

Push Deﬂector Remote forward to throw snow lower.

Pull Deﬂector Remote back to throw snow higher.

Discharge Chute

Discharge Chute rotates 220°.

ALWAYS position discharge chute straight ahead while

starting unit.

Chute Crank Handle (119,120,330,334)

Rotate the Chute with Discharge Chute Crank Handle.

IMPORTANT: DO NOT force frozen Chute controls.

Start engine and run for 3-5 minutes to thaw. If still

frozen, take to warm place until controls are free.

Chute Rotation Switch (502,503)

Press the chute rotation

switch right (1) to rotate

chute clockwise. Press the

chute rotation switch left

(2) to rotate chute

counterclockwise.

Heated Handles

Turn the heated handles switch to the

ON (1) position to activate. Turn the

switch to the OFF (2) position to

deactivate.

Differential Lock (120,333,334,502,503)

Differential Lock knob is located on the Left

Wheel Hub. With differential locked power is

applied equally to both wheels.

To engage differential lock:

• Pull and turn knob to LOCKED (1)

position and release (knob will snap in

place when positioned correctly).

To resume differential action for transport:

• Pull and turn knob to UNLOCKED (2) position

and release.

Axle Lock Pin (119)

The axle lock pin is located on the right wheel hub.

Moving pin from the hub to the axle shaft allows the

right wheel to turn freely.

Scraper Blade

The scraper blade allows the back of the housing to

keep better contact with the surface being cleared. It

also prevents damage to the housing from normal

wear.

IMPORTANT: DO NOT allow Scraper Blade to wear

too far or Auger/Impeller housing will become

damaged.

Runners

For operation on gravel surface, lower Runners so that

housing will not pick up gravel. On concrete, blacktop

or packed snow surfaces raise Runners so that

Scraper Blade scrapes clean.

Headlight

NOTE: Lamp remains on at all times for longer lamp

life. Lamp is more sensitive to fatigue when unlit.

FILLING FUEL TANK

To add fuel to Fuel Tank:

1. ALWAYS place unit in open or well ventilated

area.

2. Stop engine and allow to cool.

3. Clean Fuel Cap and surrounding area to prevent

dirt from entering Fuel Tank.

4. Remove Cap.

OS1970

OS1950

WARNING: FLAMMABLE FUEL and its

EXPLOSIVE VAPORS can result in death or

serious injury.

Handle fuel with extreme care. ALWAYS use

an approved fuel container.

No Smoking! No Lighted Materials!

No Open Flames!

Allow engine to cool before any service.

OL2730

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 24 25

Comments to this Manuals

No comments

Ariens SNO-THRO 924333 - 1024 User Manual Page 12

Comments to this Manuals

Related products and manuals for Cars Ariens SNO-THRO 924333 - 1024