Owner/Operator ManualModels921004 – ST924DLE 921005 – ST927LE921006 – ST1130DLE921007 – ST924LET921008 – ST927LET921009 – ST1130LETSno-Thro®03389300
GB - 10NOTE: After the chute rod has been inserted through the hex hole in the control assembly, placing the unit in the service position (see Service
GB - 114. Insert the short end of the chute rod into the hole in the front of the control panel.5. Connect the chute crank to the pinion gear on chute
GB - 12Check Track Tension (921007, 008, 009)Check tracking of unit and tension of tracks (see Track Tension Adjustment (921007, 008, 009) on page 34)
GB - 131. Attachment Clutch Lever2. Speed Selector3. Traction Drive Clutch Lever4. Chute Control5. Oil Fill/Dipstick6. Discharge Chute Deflector7. Dis
GB - 141. Attachment Clutch Lever2. Speed Selector3. Deflector Remote Control 4. Chute Control5. Traction Drive Clutch Lever6. Oil Fill/Dipstick7. Dis
GB - 151. Attachment Clutch Lever2. Speed Selector3. Deflector Remote Control 4. Chute Control5. Traction Drive Clutch Lever6. Oil Fill/Dipstick7. Dis
GB - 16CONTROLS AND FEATURESSee CONTROLS and FEATURES on page 13 for all Controls and Features locations.Dual Handle Interlock When Attachment Clutch
GB - 17Speed SelectorPosition the Speed Selector in the appropriate speed notch to control forward and reverse travel.Forward:(6) Fastest(1) Slowest R
GB - 18Discharge Chute Discharge chute rotates 200°.ALWAYS position discharge chute in safe direction and angle, away from operator and bystanders, be
GB - 19Track Angle (921007, 008, 009)(Figure 19)The track angle can be adjusted to position the auger housing for level clearing, deep cutting or tran
GB - 2SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . 4ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . 8CONTROLS and FEATURES. . . .
GB - 20 2. Check Function of ClutchesIf clutches do not engage or disengage properly, adjust or repair before operation. See Attachment Clutch/Brake A
GB - 214. Make sure that the traction clutch and attachment drive clutch levers are fully disengaged.5. Push Primer Bulb 2 or 3 times for cold engine.
GB - 22Ariens Dealers will provide any service or adjustments which may be required to keep your unit operating at peak efficiency. Should engine serv
GB - 23If clutches do not engage or disengage properly, adjust or repair before operation. See Attachment Clutch/Brake Adjustment on page 28 and Trac
GB - 24GENERAL LUBRICATIONIMPORTANT: Wipe each fitting clean before and after lubrication. Do not wipe gearcase filler plug; wiping the gearcase fille
GB - 25SHEAR BOLTSIMPORTANT: Use only Ariens shear bolts for replacement. Use of any other type of shear bolt may result in severe damage to unit. See
GB - 264. To adjust deflector higher: Slide cable up. Tighten top nut.5. Check travel and repeat adjustment as necessary.DISCHARGE CHUTE (921004, 006,
GB - 27DISCHARGE CHUTE (921005)If discharge chute does not stay in position while operating, tighten nut on carriage bolt at pivot point to increase t
GB - 28ATTACHMENT CLUTCH/BRAKE ADJUSTMENT(Figures 33, 34 and 35)Remove Attachment Cable Slack1. Remove the belt cover.2. Loosen jam nut on cable adjus
GB - 29Adjust the Attachment Clutch Cable Spring Extension1. Check the attachment clutch cable spring extension. Measure the length of the attachment
GB - 3• Record Unit Model and Serial numbers here.• Record Engine Model and Serial numbers here.PRODUCT REGISTRATIONThe Ariens dealer must register th
GB - 30Check Attachment BrakeSee Figure 38.1. With the clutch lever disengaged, brake pad must contact attachment belts. With clutch lever engaged, br
GB - 31a. With the traction drive clutch lever disengaged, loosen the jam nut on the cable adjuster.b. Turn the adjuster body up the cable to decrease
GB - 328. Remove hex bolts securing housing to frame (two on each side). Tip housing and frame apart on pivot pin (Figure 43).9. Remove attachment dri
GB - 332. To gain belt clearance, remove swing gate spacer and slide drive plate over so that finger clears stop hole in frame and can swing past it.
GB - 34TRACK TENSION ADJUSTMENT (921007, 008, 009)Check the track tension by applying pressure on the track midway between the upper and rear track ro
GB - 35SHORT TERMIMPORTANT: NEVER spray unit with high pressure water or store unit outdoors.Run with attachment clutch engaged a few minutes after ea
GB - 36 TROUBLESHOOTINGPROBLEM PROBABLE CAUSE CORRECTION Engine will not crank/start.1. Fuel tank is empty.2. Fuel shut-off valve closed.3. Build up o
GB - 37SPECIFICATIONSModel Number 921004 921005 921006DescriptionST924DLE ST927LE ST1130DLEEngine - TecumsehLH318SATecumsehLH318SATecum sehLH358SAPow
GB - 38SPECIFICATIONSModel Number 921007 921008 921009DescriptionST924LET ST927LET ST1130LETEngine - TecumsehLH318SATecum sehLH358SAPower Max - HP (k
ARIENS COMPANYGRAVELY® | STENS® | LOCKE® | NATIONAL® | BYNORM® | EVERRIDE® | GREAT DANE® Snow_200839 of 40Three-Year Limited Sno-Thro® WarrantyAriens
GB - 4SAFETY ALERTSLook for these symbols to point out important safety precautions. They mean:Attention! Personal Safety Is Involved!Become Alert!
ARIENS COMPANYGRAVELY® | STENS® | LOCKE® | NATIONAL® | BYNORM® | EVERRIDE® | GREAT DANE® Snow_200840 of 40Limitations• Batteries are warranted only f
Ariens Company655 West Ryan StreetBrillion, WI 54110-1072920-756-2141Fax 920-756-2407www.ariens.com
GB - 52. DANGER! 3. DANGER!SAFETY RULESRead, understand, and follow all safety practices in Owner/Operator Manual before beginning assembly or operati
GB - 6DO NOT operate near drop-offs, ditches, or embankments. Unit can suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an ed
GB - 7Check clutch and brake operation frequently. Adjust and service as required. All motion of drive wheels and auger/impeller must stop quickly whe
GB - 8PACKAGE CONTENTSASSEMBLYTools Required:•Pliers• Open-End Wrenches: 3/8, 7/16, 1/2, 9/16 in. and/or Adjustable Wrench• Tire GaugeUnfold Handlebar
GB - 9Install Discharge Chute and Discharge Chute Crank (921004, 006, 007, 008, 009)(Figure 6)1. Grease underside of discharge chute ring (if not alre
Comments to this Manuals