Ariens A173K22 (96146500) Specifications Page 11

  • Download
  • Add to my manuals
  • Print
  • Page
    / 44
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 10
LAWN MOWER
Alwaysobserve safety rules when per-
forming any maintenance.
TIRES
Keep tires free of gasoline, oil, or insect
control chemicals which can harm rubber.
Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may
cause tire damage.
DRIVE WHEELS
Check front drive wheels each time before
you mow to be sure they move freely,
The wheels not turning freely means trash,
grasscuttings, etc.arein the drive wheel area
and must be cleaned to free drive wheels.
If necessary to clean the drive wheels, be
sure to clean both front wheels.
1. Remove hubcaps, Iocknuts & washers.
2. Remove wheels from wheel adjusters.
3. Remove any trash or grass cuttings
from inside the dust cover, pinion and/
or drive wheel gear teeth.
4. Put wheels back in place.
NOTE: Ifafter cleaning,the drive wheels
do not turn freely, contact a qualified
service center.
BLADE CARE
For best results, blade must be kept sharp.
Replace a bent or damaged blade.
_CAUTION: Useonly a replacement blade
approved bythe manufacturerof your mower.
Using a blade not approved by the manu-
facturer of your mower is hazardous, could
damage yourmowerand voidyourwarranty.
TO REMOVE BLADE
1. Disconnect spark plug wire from spark
plug and place wire where itcannot
come in contact with plug.
2. Turn lawn mower on itsside. Make
sure air filter and carburetor are up.
3. Use a wood block between blade and
mower housing to prevent blade from
turning when removing blade bolt.
NOTE: Protect your hands with gloves
and/or wrap blade with heavy cloth.
4. Remove blade bolt by turning counter-
clockwise.
5. Remove blade & attaching hardware
(bolt, lock washer & hardened washer).
TO REPLACE BLADE
1. Position biade on the blade adapter
aligning the two (2) holes in the blade
with the raised lugs on the adapter.
2. Be sure the trailing edge of blade (oppo-
sitesharp edge) is uptoward the engine.
3. Install the blade bolt with the look
washer and hardened washer into
blade adapter and crankshaft.
11
4. Use block of wood between blade and
lawn mower housing and tighten the
blade bolt, turning clockwise.
Recommendedtighteningtorque:35-40ft.lbs.
IMPORTANT: Blade boit is heat treated.
Ifbolt needs replacing, replace only with
approved bolt shown in the Repair Parts
section of this manual.
Bladeadapter Key
Lockwasher _ J!
Blade Hardenec
bolt washer
Trailingedge"
Crankshaft
_"__.. keyway
Crankshaft retainer
TO SHARPEN BLADE
NOTE: We do not recommend sharpening
the blade - but if you do, be sure the blade
is balanced. Care should be taken to keep
the blade balanced.An unbalanced bladewill
cause eventual damage tomower or engine.
The blade can be sharpened with afile
or on a grinding wheel. Do not attempt
to sharpen while on the mower.
To check blade balance, drive a nail into
a beam or wall. Leave about one inch of
the straight nail exposed. Place center
hole of blade over the head of the nail.
If blade is balanced, it should remain in
a horizontal position. If either end of the
blade moves downward, sharpen the
heavy end until the blade is balanced.
GRASS CATCHER
The grass catcher maybe hosed with
water, but must be dry when used.
° Check your grass catcher often for dam-
age or deterioration. Through normal
use itwillwear. If catcher needs replac-
ing, replace only with approved replace-
ment catcher shown in the Repair Parts
section of this manual. Give the lawn
mower model number when ordering.
GEAR CASE
To keep your drivesystem working
properly,the gear case and area around
the ddve should be kept clean and free
of trash build-up. Clean under the drive
cover twice a season.
The gear case is filled with lubricant to the
proper levelat the factory. The only time
the lubricant needs attention is if service
has been performed on the gear case.
If lubricant isrequired, use only Texaco
Starplex Premium 1Grease, Part No.
750369. Do not substitute,
Page view 10
1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 43 44

Comments to this Manuals

No comments