Owner/Operator ManualModels932037 - 724 932038 - 5520932039 - 624932505 - 724932507 - 520932508 - 624Sno-Thro®00295500A 7/04Supersedes 00295500Printed
GB - 10Install Discharge Chute and Chute Crank (932037, 039, 505, 507, 508)(Figure 5, 6, and 7)NOTE: See Figure 5 for the items to install on the unit
GB - 11Discharge Chute (932038)1. Grease discharge chute ring if not already greased (Figure 8).2. Remove mounting hardware from top of engine.3. Inst
GB - 121. Traction Drive Clutch Bail2. Speed Selector3. Chute Crank (932037, 039, 505, 507, 508)4. Muffler Guard (932037, 039, 505, 507, 508)5. Discha
GB - 13CONTROLS AND FEATURESSee Figure 9 for all Controls and Features locations.Traction Drive Clutch - Left Hand BailSqueeze the Traction Drive Clut
GB - 141. Choke Closed position: chokes off air to engine for easier start.2. Choke Open position: allows for normal operation.IMPORTANT: Gradually op
GB - 15Axle Lock Pin (Figure 10)Use the axle lock pin to lock or unlock the right wheel. Lock the right wheel to increase traction; unlock the right w
GB - 164. Adjust RunnersCheck and adjust Runners (see Service and Adjustments). Allow 1/8 in. (3 mm) between scraper blade and hard, smooth surface(s)
GB - 17Shut Off1. Release Traction Drive Clutch Bail and allow unit to come to a complete stop.2. Run Impeller a few minutes after use to prevent free
GB - 18MAINTENANCE SCHEDULEThe chart below shows the recommended maintenance schedule that should be performed on a regular basis. More frequent servi
GB - 19GENERAL LUBRICATIONIMPORTANT: Wipe each fitting clean before and after lubrication.IMPORTANT: DO NOT allow grease or oil to get on friction dis
2Ariens Company655 West Ryan StreetP.O. Box 157Brillion, Wisconsin 54110-0157 USATelephone (920) 756-2141Facsimile (920) 756-2407EC DECLARATION OF CON
GB - 20RUNNERSRunners should be adjusted as conditions require (Figure 15).1. Position unit on a hard, flat, smooth level surface. 2. Adjust runners b
GB - 212. Pull shift rod and adjustment pivot pin out of speed selector lever.3. Place the speed selector lever in the fastest forward speed position.
GB - 22Replace Attachment Drive Belt1. Place new belt onto lower pulley and while holding brake out of way, tip unit together.2. Secure blower housing
GB - 23TRACTION DRIVE BELT REPLACEMENTNOTE: Housing and frame must be tipped apart and attachment drive belt removed from engine sheave in order to ch
GB - 24c. To decrease the distance between the clutch bail and handlebar, move the idler away from the attachment belt.d. Tighten idler adjustment nut
GB - 25FRICTION DISC REPLACEMENTRemove Friction Disc(Figure 24):1. Shut off engine, remove key, disconnect spark plug wire and allow unit to cool comp
GB - 269. Reinstall one nut to keep the inside bearing cap in place.10. Remove bearing cap/bushing and washer from right side of unit.11. Reinstall nu
GB - 27To obtain a complete parts manual, find your model and serial number. Then go to www.ariens.com or call 1-920-756-4688.SERVICE PARTSOrder the f
GB - 28Does not operate in Forward/Reverse.1. Friction disc not adjusted properly.2. Traction belt not functioning.1. Repair or replace friction disc.
GB - 29SPECIFICATIONSModel Number 932037 932038 932039 932505 932507 932508Description 724 5520 624 724 520 624Engine - Tecumseh OH195SA LH195SP OH195
3CE Sound and Vibration – Niveau sonore et vibration CE – CE-Geräuschpegel und Vibrationswerte – Livello sonoro e vibrazioni CE – Sonido y vibración C
GB - 303-Year Limited Sno-Thro WarrantyAriens Company warrants to the original purchaser that consumer products manufacturedby Ariens Company will be
Ariens Company655 West Ryan StreetP.O. Box 157Brillion, WI 54110-0157920-756-2141Fax 920-756-2407www.ariens.comThe engine exhaust from this productco
GB - 4Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Controls and
GB - 5DISCLAIMERAriens reserves the right to discontinue, make changes to, and add improvements upon its products at any time without public notice or
GB - 6REQUIRED OPERATOR TRAININGOriginal purchaser of this unit was instructed by the seller on safe and proper operation. If unit is to be used by so
GB - 72. DANGER! 3. DANGER!SAFETY RULESRead, understand, and follow all safety practices in Owner/Operator Manual before beginning assembly or operati
GB - 8Never direct discharge towards persons or property that may be injured or damaged by thrown objects. Use extreme caution on gravel surfaces. Sta
GB - 9This product is equipped with an internal combustion type engine. DO NOT use unit on or near any unimproved, forest-covered or brush covered lan
Comments to this Manuals