Ariens 936042 Specifications download pdf (Page 28)

TROUBLESHOOTING

PROBLEM

Engine continues

to run when oper=

ator leaves seat

with attachment

clutch engaged

Poor cut = uneven

Mower blades will

not rotate

Poor grass

discharge

Headlight(s) not

working

(if so equipped)

Battery will not

charge

Loss of drive

Engine "back=

fires" when turn=

ing engine "OFF"

Engine dies when

tractor is shifted

into reverse

CAUSE

1. Faulty operator-safety presence control

system.

1. Worn, bent or loose blade.

2. Mower deck not level.

3. Buildup of grass, leaves, trash under mower.

4. Bent blade mandrel.

5. Clogged mower deck vent holes from

buildup of grass, leaves, and trash around

mandrels.

1. Obstruction in clutch mechanism.

2. Worn/damaged mower drive belt.

3. Frozen idler pulley.

4. Frozen blade mandrel.

1. Engine speed too stow.

2. Travel speed too fast.

3. Wet grass.

CORRECTION

1. Check wiring, switches and connections. If not

corrected, contact an authorized service center/

department.

1. Replace blade. Tighten blade bolt.

2. Level mower deck.

3. Clean underside of mower housing.

4. Replace blade mandrel.

5. Clean around mandrels to open vent holes.

1. Remove obstruction.

2. Replace mower drive belt.

3. Replace idler pulley.

4. Replace blade mandrel.

1. Place throttle control in "FAST" position.

2. Shift to slower speed.

3. Allow grass to dry before mowing.

4. Mower deck not level.

5. Low/uneven tire air pressure.

6. Worn, bent or loose blade.

7. Buildup of grass, leaves, trash under mower.

8. Mower drive belt worn.

9. Blades improperly installed.

10. Improper blades used.

11. Clogged mower deckvent holesfrom buildup

of grass, leaves, trash around mandrels.

1. Switch is "OFF".

2. Bulb(s) or lamp(s) burned out.

3. Faulty light switch.

4. Loose or damaged wiring.

5. Blown fuse.

4. Level mower deck.

5. Check tires for proper air pressure.

6. Replace blade. Tighten blade bolt.

7. Clean underside of mower housing.

8. Replace mower drive belt.

9. Reinstall blades sharp edge down.

10. Replace with blades listed in parts manual.

11. Clean around mandrels to open vent holes.

1. Turn switch "ON".

2. Replace bulb(s) or lamp(s).

3. Check/replace light switch.

4. Check wiring and connections.

5. Replace fuse.

1. Bad battery cell(s).

2. Poor cable connections.

3. Faulty regulator (if so equipped).

4. Faulty alternator.

1. Freewheel control in "disengaged" position.

2. Debris on steering plate (if equipped).

3. Motion drive belt worn, damaged, or broken.

4. Air trapped in transmission during

shipment or servicing.

5. Axle key missing.

1. Engine throttle control not set between

half and full speed (fast) position before

stopping engine.

1. Reverse operation system (ROS) is not"ON"

while mower or other attachment is engaged.

1. Replace battery.

2. Check/clean all connections.

3. Replace regulator.

4. Replace alternator.

1. Place freewheel control in "engaged" position.

2. See "CLEANING" in the maintenance section.

3. Replace motion drive belt.

4. Purge transmission.

5. Install axle key at rear wheel. See "TO REMOVE

WHEEL" in the Service and Adjustments section.

1. Move throttle control between half and full speed

(fast) position before stopping engine.

1. Turn ignition key to ROS "ON" position. See

Operation section.

28

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 63 64

Comments to this Manuals

No comments