Ariens 926057 Specifications download pdf (Page 15)

EN - 15

5. Pull recoil starter handle with a rapid

continuous full arm stroke. Let rope

rewind slowly.

IMPORTANT: DO NOT let Starter Handle

snap against Starter.

NOTE: When operating unit in the winter

months, recoil guard foam cover must be

installed. See Recoil Guard Foam Cover

Installation on page 20.

6. Repeat until engine starts. (If engine

does not start, refer to Troubleshooting

on page 28.)

7. Adjust choke as needed.

8. Set throttle to Part Throttle or Slow

position to adapt to outside temperature

or travel speed. Set throttle to Fast

position for normal operation.

Electric Start (120V)

1. Connect extension cord to starter.

IMPORTANT: Prevent damage to unit. Know

voltage of your starter and only use matching

outlets.

2. Plug extension cord into 120V, 3-wire,

grounded outlet.

IMPORTANT: Use only Ariens extension cord

(P/N 02483100) or an equivalent cord that is

rated for a minimum of 13 amps, grounded,

UL listed, CSA certified and labeled as

suitable for outdoor use.

3. Make sure that traction clutch lever and

attachment clutch lever are fully

disengaged.

4. Turn engine shut-off switch to “ON”

position.

5. If engine is cold, apply choke. A warm

engine requires less choking than a cold

engine. See Engine Manual for detailed

instructions.

6. Set throttle to proper starting position.

7. Press starter button on engine until

engine starts.

IMPORTANT: DO NOT operate starter more

than 15 seconds per minute, as overheating

and damage can occur. (If engine does not

start, refer to Troubleshooting on page 28.)

8. Adjust choke as needed.

9. Disconnect power cord from outlet, then

starter.

10. Set throttle to Part Throttle or Slow

position to adapt to outside temperature

or travel speed. Set throttle to Fast

position for normal operation.

Shut Off

1. Release both clutch levers and wait for

all moving parts to come to a complete

stop.

2. Run unit a few minutes after use to

prevent freeze-up.

3. Move throttle to STOP position.

4. Turn engine shut-off switch to “OFF”

position.

USING THE BRUSH

After proper Pre-Start and Starting:

1. Select speed control position and

direction.

IMPORTANT: DO NOT overload unit capacity

by sweeping at too fast a rate.

2. Engage the traction drive clutch first.

3. Engage the attachment clutch next.

Tips for Sweeping

To clear an area, run unit in an overlapping

series of paths. For large areas, start in the

middle and sweep debris to each side, so it is

not cleared more than once.

ALWAYS direct discharge away from area to

be cleared and with direction of the wind.

Snow is best removed as soon as possible

after snow fall.

Tips for De-thatching

De-thatch in the spring to clear winter

undergrowth.

Adjust brush height so it just touches the

grass.

Set the brush angle full left or full right so

thatch gets cleared only once.

De-thatch dry grass.

Use a slow speed to clear thatch without

damaging the lawn.

TRAVELING

To travel from one work area to another:

1. Set throttle to SLOW position or slightly

higher.

2. Press down the handlebars enough to

raise the front of the unit slightly off the

surface.

3. Engage traction clutch without engaging

the attachment drive clutch.

TRANSPORT

ALWAYS shut off engine and close fuel shut-

off when transporting unit on a truck or trailer.

Use extra care when loading or unloading

unit onto trailer or truck.

Secure unit chassis to transport vehicle.

NEVER secure from rods or linkages that

could be damaged.

DO NOT transport machine while engine is

running.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 33 34

Comments to this Manuals

No comments