Ariens Snow Blower 920006 User Manual download pdf (Page 17)

GB - 17

9. Repeat steps 7 and 8 until engine starts.

(If engine does not start, refer to

TROUBLESHOOTING on page 30.)

10. Adjust choke as needed.

11. Set throttle to Part Throttle or Slow

position for adaptation to outside

temperature or travel. Set throttle to Fast

position for normal operation.

Electric Start (120V)

1. Connect extension cord to starter.

IMPORTANT: Prevent damage to unit. Know

voltage of your starter and only use matching

outlets.

2. Plug extension cord into 120V 3-wire,

grounded outlet.

IMPORTANT: Use only Ariens extension cord

(P/N 02483100) or an equilavent cord that is

rated for a minimum of 13 amps, grounded,

UL listed, CSA certified and labeled as

suitable for outdoor use.

3. Turn discharge chute straight ahead.

4. Make sure that the traction clutch and

attachment drive clutch levers are fully

disengaged.

5. Push Primer Bulb 2 or 3 times for cold

engine.

NOTE: When temperature is below -15° F

(-26° C) additional priming may be needed.

6. Insert key into ignition switch on engine

and push into "Run" position. DO NOT

twist key after it is inserted.

7. If engine is cold, apply choke. A warm

engine requires less choking than a cold

engine. See Engine Manual for detailed

instructions.

8. Set throttle to proper starting position

9. Press starter button on engine until

engine starts.

IMPORTANT: DO NOT operate starter more

than 15 seconds per minute, as overheating

and damage can occur. (If engine does not

start, refer to TROUBLESHOOTING on

page 30.)

10. Adjust choke as needed.

11. Disconnect power cord from outlet, then

starter.

12. Set throttle to Part Throttle or Slow

position for adaptation to outside

temperature or travel. Set throttle to Fast

position for normal operation.

Shut Off

1. Release Traction Drive Clutch Lever and

allow unit to come to a complete stop.

2. Run Impeller a few minutes after use to

prevent freeze-up of Impeller.

3. Release Attachment Clutch Lever and

wait for all moving parts to come to a

complete stop.

4. Move Throttle to the “Stop” position

5. Remove key.

SNOW REMOVAL

IMPORTANT: Allow unit and engine to adjust

to the outdoor temperature before clearing

snow.

NOTE: Attachment clutch should be engaged

before wheel drive clutch when throwing

snow.

1. Select Speed Control position and

direction.

2. Engage Attachment Clutch - Right Hand

Lever.

3. Engage Traction Drive Clutch - Left

Hand Lever.

IMPORTANT: DO NOT overload unit capacity

by attempting to clear snow at too fast a rate.

Use slow speed to clear deep or hard packed

snow.

Tips for Operation

Snow is best removed as soon as possible

after snow fall.

To clear an area, run unit in an overlapping

series of paths. For large areas, start in the

middle and throw snow to each side, so snow

is not cleared more than once.

ALWAYS direct snow away from area to be

cleared and with direction of the wind.

TRAVELING

To travel from one work area to another:

1. Set Throttle to Slow or Part-Throttle

position.

2. Press down on handlebars enough to

raise front of unit slightly off surface.

3. Engage wheel drive clutch without

engaging attachment drive clutch.

TRANSPORT

ALWAYS shut off engine, remove key, and

close fuel shut-off valve when transporting

unit on a truck or trailer.

Use extra care when loading or unloading

unit onto trailer or truck.

Secure unit chassis to transport vehicle.

NEVER secure from rods or linkages that

could be damaged.

DO NOT transport machine while engine is

running.

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 33 34

Comments to this Manuals

No comments