Owner/Operator ManualManuel Du Propriétaire/UtilisateurModels926037 – Pro 26926038 – Pro 28926039 – Pro 32926040 – Pro 36926041 – Pro-Track 26926042 –
GB - 109. Connect the chute lock cable to the lock arm by fitting the cable ball end into the slot on the lock arm and then insert the chute lock cabl
GB - 11Check Function of Dual Handle InterlockWithout the engine running, press down (engage) both clutch levers. Release attachment clutch lever. Att
GB - 121. Oil Drain2. Fuel Shut-Off Valve3. Primer Bulb4. Recoil Starter Handle5. Throttle (Engine Stop)6. Choke Control Knob7. Ignition Key (Push/Pul
GB - 13CONTROLS AND FEATURESSee CONTROLS and FEATURES on page 12 for all Controls and Features locations.Dual Handle Interlock When Attachment Clutch
GB - 14Speed SelectorPosition the Speed Selector in the appropriate speed notch to control forward and reverse travel.Forward:(6) Fastest(1) Slowest R
GB - 15Discharge Chute Control (Figure 12)IMPORTANT: If chute does not stay in set position, adjust as directed in Discharge Chute Control on page 25
GB - 16Drift Cutters(Figure 14)Drift cutters break up snow drifts that are taller than the auger housing and direct the snow into the auger. Store the
GB - 17FILLING FUEL TANKGASOLINEIMPORTANT: ALWAYS use gasoline that meets the following guidelines:• Clean, fresh gasoline.• A minimum of 87 octane/87
GB - 18 4. Check Axle Lock (926041, 042, 043)Use the axle lock knob to lock or unlock the right side differential. Lock the differential to engage bot
GB - 1912. Set throttle to Part Throttle or Slow position for adaptation to outside temperature or travel. Set throttle to Fast position for normal op
GB - 2SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . 4ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . 8CONTROLS and FEATURES . . . .
GB - 20Ariens Dealers will provide any service or adjustments which may be required to keep your unit operating at peak efficiency. Should engine serv
GB - 21MAINTENANCE SCHEDULEThe chart below shows the recommended maintenance schedule that should be performed on a regular basis. More frequent servi
GB - 22To ensure adequate lubricant level:1. Remove filler plug. Lubricant must be at least up to bottom of lubricant filler hole with unit resting on
GB - 23Replace Fuse (926104, 105)1. Remove the two screws and the cover plate from beneath the battery.2. Locate the fuse holder on the wiring harness
GB - 24SHEAR BOLTS(Figure 22)IMPORTANT: Use only Ariens shear bolts for replacement. Use of any other type of shear bolt may result in severe damage t
GB - 257. Check and adjust attachment clutch, speed selector and traction clutch. See Speed Selector Adjustment on page 25.8. Re-install bottom cover.
GB - 268. Adjust pivot pin on the shift rod as necessary so unit travels forward when speed selector is in first forward position and travels backward
GB - 27Check Attachment Idler Arm Roller Clearance(Figure 30)NOTE: It will be difficult to check the measurement inside the frame. Use a 1/2 in. (12.7
GB - 28Check Attachment Brake(Figure 33)1. With the clutch lever disengaged, brake pad must contact attachment belts. With clutch lever engaged, brake
GB - 29TRACTION DRIVE CLUTCH ADJUSTMENT(Figure 35)If drive slips, adjust traction clutch to compensate for friction disc wear.To adjust traction clutc
GB - 3• Record Unit Model and Serial numbers here.• Record Engine Model and Serial numbers here.PRODUCT REGISTRATIONThe Ariens dealer must register th
GB - 30ATTACHMENT DRIVE BELTS REPLACEMENT(Figure 36)Remove old attachment drive belts:1. Shut off engine, remove key, disconnect spark plug wire and a
GB - 31TRACTION DRIVE BELT REPLACEMENT(Figure 37)NOTE: Replacement will be easier with housing and frame tipped apart and bottom cover off. 1. Remove
GB - 32BATTERY (926104, 105)Charging1. Place unit on a level surface and shut off engine.2. Disconnect negative (–) cable first, then positive (+) cab
GB - 33SHORT TERMIMPORTANT: NEVER spray unit with high pressure water or store unit outdoors.Run with attachment clutch engaged a few minutes after ea
GB - 34 TROUBLESHOOTINGPROBLEM PROBABLE CAUSE CORRECTION Engine will not crank/start.1. Fuel tank is empty.2. Fuel shut-off valve closed.3. Build up o
GB - 35SPECIFICATIONSModel Number 926037 926038 926039 926040DescriptionPro 26 Pro 28 Pro 32 Pro 36EngineEngine Model Briggs & Stratton Polar Forc
GB - 36SPECIFICATIONSModel Number 926041 926042 926043DescriptionPro-Track 26 Pro-Track 28 Pro-Track 32EngineEngine Model Briggs & Stratton Polar
GB - 37SPECIFICATIONSModel Number 926104 926105DescriptionPro 32 Pro 36EngineEngine Model Briggs & Stratton 1650 SeriesGross Torque* - ft-lbs (N-m
ARIENS COMPANYGRAVELY® | STENS® | LOCKE® | NATIONAL® | BYNORM® | EVERRIDE® | GREAT DANE® Snow_201038Three-Year Limited Sno-Thro® WarrantyAriens Compa
ARIENS COMPANYGRAVELY® | STENS® | LOCKE® | NATIONAL® | BYNORM® | EVERRIDE® | GREAT DANE® Snow_201039Limitations• Batteries are warranted only for a p
GB - 4SAFETY ALERTSLook for these symbols to point out important safety precautions. They mean:Attention! Personal Safety Is Involved!Become Alert!
Ariens Company655 West Ryan StreetBrillion, WI 54110-1072920-756-2141www.ariens.com
GB - 51. WARNING!2. DANGER! 3. DANGER!EMISSION CONTROL SYSTEMThis equipment and/or its engine may include exhaust and evaporative emissions control sy
GB - 6NEVER allow children to operate or play on or near unit. Be alert and shut off unit if children enter area.DO NOT allow adults to operate unit w
GB - 7Check clutch and brake operation frequently. Adjust and service as required. All motion of drive wheels and auger/impeller must stop quickly whe
GB - 8NEVER store unit with fuel in fuel tank, inside a building where any ignition sources are present such as hot water heaters, space heaters, or c
GB - 9Install Discharge Chute and Discharge Chute Rod(Figure 5, 6, 7 and 8)1. Grease underside of discharge chute ring (if not already greased).2. Rem
Comments to this Manuals