Owner/Operator Manual Models 932035 - 724932503 - 724932101 - 824932309 - 824 Sno-Thro ® 03245600D 4/02Supercedes 03245600,A,B,CPrinted in USA ENGLIS
GB - 10Never direct discharge towards persons or property that may be injured or damaged by thrown objects. Use extreme caution on gravel surfaces. S
GB - 11 Spark Arrester This product is equipped with an internal combustion type engine. DO NOT use unit on or near any unimproved, forest-covered or
GB - 12 Tools Required: • Pliers• Open-End Wrenches: 3/8, 7/16, 1/2, 9/16" and/or Adjustable Wrench• Tire Gauge ASSEMBLY Handlebar and Shift Rod
GB - 13 Check Function of Dual Handle Interlock (932101, 309) Without the engine running, press down (engage) both clutch levers. Release attachment
GB - 14 Run in Attachment Belt 1. Start unit in a well-ventilated area according to Starting and Shut-Off in Operation .2. Engage attachment clutc
GB - 15Choke Control Knob1. Choke Closed position: chokes off air to engine for easier start.2. Choke Open position: allows for normal operation.IMPOR
GB - 16PRE-START1. Frozen ImpellerIMPORTANT: Before starting engine, check impeller to be sure it is not frozen.To check impeller:1. With key in “Stop
GB - 17Electric Start (120V or 240V)(932035, 101, optional on 309, 503)1. Connect extension cord to prongs on starter.IMPORTANT: Prevent damage to uni
GB - 18Ariens Dealers will provide any service or adjustments which may be required to keep your unit operating at peak efficiency. Should engine serv
GB - 19CLEAN ENGINERefer to Engine Manual for detailed instructions.CHECK ENGINE OILThe engine crankcase oil should be checked every 5 hours of operat
2 4/29/02MODEL CERTIFICATE OF CONFORMITY ISSUED BY THE MANUFACTURERCERTIFICAT DE CONFORMITÉ DU MODÈLE DÉLIVRÉ PAR LE FABRICANT MODELL-KONFORMITÄTSBES
GB - 20DISCHARGE CHUTE DEFLECTOR Deflector must stay in selected position while throwing snow. To adjust, loosen then retighten hardware to desired defl
GB - 21RUNNERSRunners should be adjusted (Figure 11) as conditions require.1. Position unit on a hard, flat, smooth level surface. 2. Adjust runners by
GB - 22SPEED SELECTOR ADJUSTMENTTo adjust (Figure 13):1. Remove hair pin from adjustment pivot pin.2. Pull shift rod and adjustment pivot pin out of s
GB - 23Replace Attachment Drive Belt1. Place new belt onto lower pulley and while holding brake out of way, tip unit together.2. Secure blower housing
GB - 24TRACTION DRIVE BELT REPLACEMENTNOTE: Housing and frame must be tipped apart and attachment drive belt removed from engine sheave in order to ch
GB - 258. Check belt finger clearance.With clutch lever engaged, belt fingers should be 1/16–1/8 in (1.6-3 mm) from belt. Adjust belt fingers as necessar
GB - 26FRICTION DISC REPLACEMENT (932035, 503)Remove Friction Disc(Figure 19):1. Shut off engine, remove key, disconnect spark plug wire and allow uni
GB - 27FRICTION DISC REPLACEMENT (932101, 309)Remove Friction Disc (Figure 20):1. Shut off engine, remove key, disconnect spark plug wire and allow un
GB - 289. Reinstall tires with clip pins.10. Set unit upright.11. Replace spark plug wire on spark plug.SHORT TERMIMPORTANT: NEVER spray unit with hig
GB - 29To obtain a complete parts manual, find your model and serial number. Then go to www.ariens.com or call 1-800-678-5443.* Available in CE countri
3 4/29/02Stated Sound Power Levels are established following Annex V “Internal Control of Production” of directive 2000/14/EC and assessment procedur
GB - 30SPECIFICATIONSModel Number 932309 932101 932503 932035Description 824 824 724 724Engine - Tecumseh HMSK80-155700WHMSK80-155699WOHSK70-72507EOHS
GB - 313 Year Limited Sno-Thro WarrantyAriens Company warrants to the original purchaser that consumer products manufacturedby Ariens Company will be
Ariens Company655 West Ryan StreetP.O. Box 157Brillion, WI 54110-0157920-756-2141Fax 920-756-2407www.ariens.com
4 ENGLISH 1. Traction Drive Clutch Lever2. Ignition Switch, push-pull3. Choke4. Throttle (Engine Stop)5. Runner(s)6. Axle Lock Pin (932101, 309)7. Be
5Figure 1OS0502OS210012342221 201918171615145791011121386
GB - 6 Controls and Features . . . . . . . . . . . . . . . . 4Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Assembly. . . . . .
GB - 7 DELIVERY Customer Note: If you have purchased this product without complete assembly and instruction by your retailer, it is your responsibil
GB - 8 SAFETY DECALS AND LOCATIONS ALWAYS replace missing or damaged Safety Decals. Refer to figure below for Safety Decal locations. 1. DANGER! 2. WA
GB - 9 3. DANGER! 4. HOT SURFACES! ASSEMBLY SAFETY RULES Read, understand, and follow all safety practices in Owner/Operator Manual before beginning
Comments to this Manuals