Owner/Operator ManualModels921001 – ST824E921002 – ST1027LE921003 – ST1130DLE921004 – ST924DLESno-Thro®00660400 6/07Printed in USAENGLISHFRANÇAIS
GB - 102. Insert the barrel on the cable end into the bracket on left side of chute deflector (Figure 12).3. Hold seal out of the way while routing th
GB - 111. Attachment Clutch Lever2. Speed Selector3. Traction Drive Clutch Lever4. Chute Control5. Oil Fill/Dipstick6. Discharge Chute Deflector7. Dis
GB - 121. Attachment Clutch Lever2. Speed Selector3. Deflector Remote Control 4. Chute Control5. Traction Drive Clutch Lever6. Oil Fill/Dipstick7. Dis
GB - 13CONTROLS AND FEATURESSee Figure 13 for all Controls and Features locations.Dual Handle Interlock When Attachment Clutch and then Traction Drive
GB - 14Choke Control Knob1.Choke Closed position: chokes off air to engine for easier start.2.Choke Open position: allows for normal operation.IMPORTA
GB - 15Discharge Chute Control (921002, 003, 004)IMPORTANT: If chute does not stay in set position, adjust as directed in SERVICE AND ADJUSTMENTS on
GB - 16FILLING FUEL TANKFuel Shut-Off ValveIMPORTANT: The fuel shut-off valve MUST be in the closed position prior to transporting the unit.The fuel s
GB - 17STARTING AND SHUT OFFIMPORTANT: Allow unit and engine to adjust to the outdoor temperature before clearing snow. Before shut-off, run the attac
GB - 18TRAVELINGTo travel from one work area to another:1. Set Throttle to Slow or Part-Throttle position.2. Press down on handlebars enough to raise
GB - 19CLEAN ENGINERefer to Engine Manual for detailed instructions.CHECK ENGINE OILThe engine crankcase oil should be checked every 5 hours of operat
GB - 2SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GB - 20Figure 23Oil GreaseOS7136OS7141OS7142921002921002, 003, 004OS7143921001921003, 004
GB - 21SCRAPER BLADEIMPORTANT: Damage to auger/impeller housing will result if blade wears down too far.Scraper blade is adjustable to compensate for
GB - 22DEFLECTOR REMOTE (921002, 003, 004)Deflector must stay in selected position while throwing snow.If deflector does not stay in set position: 1.
GB - 23If chute does not rotate freely:Tighten the cable by loosening the upper adjustment nut, and then tightening the lower adjustment nut against t
GB - 24ATTACHMENT CLUTCH/BRAKE ADJUSTMENT(Figures 33, 34 and 35)Remove Attachment Cable Slack1. Remove the belt cover.2. Loosen jam nut on cable adjus
GB - 25Adjust the Attachment Clutch Cable Spring Extension1. Check the attachment clutch cable spring extension. Measure the length of the attachment
GB - 26Check Attachment BrakeSee Figure 38.1. With the clutch lever disengaged, brake pad must contact attachment belts. With clutch lever engaged, br
GB - 27b. Turn the adjuster body up the cable to decrease the distance between the clutch lever and handlebar.c. Turn the adjuster body down the cable
GB - 282. Tip housing and frame back together and secure with hex bolts.3. Place belt onto engine sheave.4. Reposition and secure belt fingers.IMPORTA
GB - 295. Disconnect pivot pin from the speed selector arm. Save the hardware for reinstallation.6. Remove spring clip pin nearest drive sprocket from
GB - 3DELIVERYCustomer Note: If you have purchased this product without complete assembly and instruction by your retailer, it is your responsibility
GB - 30 TROUBLESHOOTINGPROBLEM PROBABLE CAUSE CORRECTION Engine will not crank/start.1. Fuel tank is empty.2. Fuel shut-off valve closed.3. Build up o
GB - 31SPECIFICATIONSModel Number 921001 921002 921003 921004DescriptionST824E ST1027LE ST1130DLE ST924DLEEngine - TecumsehLH318SATec um se hLH358SAT
Ariens Company • 655 W. Ryan St. • Brillion, WI 54110-1072• (920) 756-2141 • www.ariens.com ALW2 - 62207Ariens Limited Warranties2-Year Limited Lawn a
Ariens Company • 655 W. Ryan St. • Brillion, WI 54110-1072• (920) 756-2141 • www.ariens.com ALW2 - 62207Exceptions, Limitations, ExclusionsThese warra
Ariens Company655 West Ryan StreetBrillion, WI 54110-1072920-756-2141Fax 920-756-2407www.ariens.com
GB - 4SAFETY DECALS AND LOCATIONSALWAYS replace missing or damaged Safety Decals. Refer to figures below for Safety Decal locations.1. WARNING!2. DANG
GB - 5ALWAYS check overhead and side clearances carefully before operation. ALWAYS be aware of traffic when operating along streets or curbs.Keep chil
GB - 6Never carry passengers.Check clutch and brake operation frequently. Adjust and service as required. All motion of drive wheels and auger/impelle
GB - 7PACKAGE CONTENTSASSEMBLYTools Required:•Pliers• Open-End Wrenches: 3/8, 7/16, 1/2, 9/16 in. and/or Adjustable Wrench•Tire GaugeUnfold Handlebar
GB - 8..Install Discharge Chute and Discharge Chute Crank (921002, 003, 004)(Figure 8)1. Grease underside of discharge chute ring (if not already grea
GB - 9NOTE: After the chute rod has been inserted through the hex hole in the control assembly, placing the unit in the service position (see Service
Comments to this Manuals