Owner/Operator Manual Manuel du Propriétaire/UtilisateurCompact Series Sno-Thro04631900E • 7/14Printed in USAENGLISHFRANÇAISE10The use of any gasoline
EN - 10Install Remote Deflector Cable(Models 920021, 022)(Figures 7 and 8)1. Pull rubber seal cap away from snap fitting (Figure 7).2. Install snap fi
EN - 11Check Tire Pressure (Models 920013, 021)Check tire pressure and adjust to the pressure listed on tire sidewall.Check Track Tension(Model 920022
EN - 121. Attachment Clutch Lever2. Speed Selector3. Traction Drive Clutch Lever4. Discharge Chute Crank5. Muffler Guard6. Remote Discharge Chute Defl
EN - 131. Attachment Clutch Lever2. Speed Selector3. Traction Drive Clutch Lever4. Discharge Chute Crank5. Muffler Guard6. Remote Discharge Chute Defl
EN - 141. Gas Tank and Cap2. Oil Fill and Dipstick3. Fuel Shut-off Valve4. Recoil Starter Handle5. Electric Starter6. Choke7. Ignition Switch8. Primer
EN - 15CONTROLS AND FEATURESSee Figures 9 – 11 for all Controls and Features locations.Dual Handle Interlock When Attachment Clutch and then Traction
EN - 16Fuel Shut-Off ValveIMPORTANT: The fuel shut-off valve MUST be in the closed position prior to transporting the unit.The fuel shut-off valve has
EN - 17Place deflector remote in a forward notch to throw snow lower. Place deflector remote in a rearward notch to throw snow higher.IMPORTANT: If Ch
EN - 18Scraper BladeThe scraper blade allows the back of the housing to keep better contact with the surface being cleared. It also prevents damage to
EN - 19IMPORTANT: DO NOT OVERFILL! This equipment and/or its engine may include evaporative emissions control system components, required to meet EPA
EN - 2SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . 4ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . 8CONTROLS and FEATURES . . . .
EN - 204. If engine is cold, apply choke. See Engine Manual for detailed instructions.NOTICE: A warm engine requires less choking than a cold engine.5
EN - 21Ariens Dealers will provide any service or adjustments which may be required to keep your unit operating at peak efficiency. Should engine serv
EN - 22CHECK CLUTCH OPERATIONAuger / impeller must stop within 5 seconds when attachment clutch lever is released.Wheels must stop quickly when tracti
EN - 23BOTTOM COVER REMOVAL(Models 920013, 021)1. Remove the six screws that attach the bottom cover (4) to the frame and remove the bottom cover.2. R
EN - 24Figure 18GreaseOilModels 920013, 0212x2x
EN - 25Figure 19GreaseOilModel 9200222x2x
EN - 26SCRAPER BLADEIMPORTANT: Damage to housing will result if blade wears down too far. Scraper blade is adjustable to compensate for wear.To adjust
EN - 27REMOTE DISCHARGE DEFLECTOR CONTROL ADJUSTMENT(Models 920021, 022)(Figures 23 and 24)Deflector must stay in selected position while throwing sno
EN - 28SPEED SELECTOR ADJUSTMENT(Figure 26)To adjust:1. Disconnect adjustment pivot pin from speed selector arm. Save hardware for reinstallation.2. P
EN - 294. Loosen jam nut on cable adjustment barrel, and then turn the adjustment barrel down to shorten cable and remove all cable slack (Figure 27).
EN - 3UNAUTHORIZED REPLACEMENT PARTSUse only Ariens replacement parts. The replacement of any part on this vehicle with anything other than an Ariens
EN - 30• If roller is less than 1/2" (12.7 mm) from frame, loosen idler adjustment nut and move idler closer to the belt. Tighten adjustment nut
EN - 31TRACTION DRIVE CLUTCH ADJUSTMENTIf drive slips, adjust traction clutch to compensate for friction disc wear. 1. Loosen jam nut on traction cabl
EN - 32Replace Attachment Drive Belt1. Place new belt onto attachment pulley (Figure 34).NOTICE: Engage attachment clutch lever while connecting housi
EN - 33TRACTION DRIVE BELT REPLACEMENT(Figure 36)NOTICE: Housing and frame must be tipped apart and attachment drive belt removed from engine sheave i
EN - 346. Remove spring clip pin nearest drive gear from hex shaft.7. Remove left bearing flange from frame.8. Slide hex shaft to the left to remove t
EN - 3513. Insert new friction disc assembly into frame. Install washers onto carrier bearing and slide into speed selector arm. 14. Slide hex shaft t
EN - 36HEIGHT ADJUSTER CABLE ADJUSTMENT(Model 920022(Figure 42)1. Make sure that height adjustment lock finger is fully engaged (Figure 42).2. Loosen
EN - 37SERVICE PARTSOrder the following parts through your Dealer:Part No. Description00036800 Ariens Hi-Temp Grease (Three 3-oz. Cartridges)21547400
EN - 38Does not operate in Forward / Reverse.1. Friction disc worn out.2. Traction belt not functioning.3. Speed selector not adjusted properly.1. Rep
EN - 39SPECIFICATIONSModel Number 920013 920022 920021DescriptionCompact 22Compact 24 TrackCompact 24Engine Ariens AXGross Torque* – lbf-ft (N•m) 9.5
EN - 4SAFETY ALERTSLook for these symbols to point out important safety precautions. They mean:Attention! Personal Safety Is Involved!Become Alert!
Sno-Chore 2013EN - 40Sno-Thro®, Sno-Tek® and Chore Performing Equipment Limited WarrantyAriens Company (Ariens) warrants to the original purchaser tha
Sno-Chore 2013EN - 41Exceptions and LimitationsThe chart below details special exceptions to this warranty:Customer ResponsibilitiesRegister the produ
Sno-Chore 2013EN - 42Exclusions – Items Not Covered by This Warranty• Parts that are not genuine Ariens, Gravely, Parker or Countax service parts are
Ariens655 West Ryan StreetBrillion, WI 54110920-756-4688Fax 920-756-2407www.ariens.comwww.ariens.com.au
EN - 5SAFETY RULESRead, understand, and follow all safety practices in Owner/Operator Manual before beginning assembly or operating. Failure to follow
EN - 6DO NOT allow adults to operate unit without proper training. Only trained adults may operate unit. Training includes actual operation.Keep area
EN - 7Run unit a few minutes after clearing snow to prevent freeze-up of attachment.Disengage attachment when not in use. Disengage all clutches befor
EN - 8Package ContentsTools Required• Pliers• Open-End Wrenches: 3/8, 7/16, 1/2, 9/16" and/or Adjustable Wrench•Tire Gauge• Torque Wrench (Option
EN - 9INSTALL DISCHARGE CHUTE AND DISCHARGE CHUTE CRANK(Figures 5 and 6)1. Grease underside of discharge chute ring (if not already greased).2. Remove
Comments to this Manuals