Ariens 911333- LM21S Specifications

Models911330 - LM21SW911333 - LM21S911334 - LM21SW911335 - LM21S911396 - PRO21SWWalk Behind Lawn Mower01271000 3/06Printed in USAENGLISHFRANÇAISDEUTSC

GB - 10CARTON CONTENTSASSEMBLY1. Unfold and adjust handlebar. See HANDLEBAR HEIGHT on page 19.NOTE: DO NOT bend the speed control rod (if equipped) wh

GB - 111. Engine/Blade Control2. Wheel Drive Control3. Adjustable and Folding Handlebars4. Swivel Wheel Lock (911330, 334, 396)5. Grass Bag6. Rear Doo

GB - 12CONTROLS AND FEATURESSee Figure 5 for locations.Engine/Blade ControlThe engine/blade control must be held against the handlebar to start the en

GB - 13Swivel Wheel Models (911330, 334, 396)To change front wheel cutting height, insert height adjuster pin into the holes that match the desired cu

GB - 14Wheel Drive Control (self-propelled models)NOTE: Engine must be running for wheel drive to propel unit.To drive forward:Slowly squeeze and hold

GB - 15To Bag1. Shut off unit.2. Install side discharge cover.3. Lift rear door.4. Hook grass bag frame on mounting flange.5. Lower rear door. If nece

GB - 16Mowing TipsCut grass when it is dry.Keep mower blades sharp.Do not set cutting height too low. For tall grass, mow twice.Do not mow too fast.Mo

GB - 17NOTE: Blades should be sharpened and balanced professionally. Contact your Ariens Dealer.To remove blade:1. Stop engine, wait for all moving pa

GB - 18CHECK DRIVE BELT (self-propelled models)Check drive belt and replace if worn or damaged. See DRIVE BELT REPLACEMENT (self-propelled models) on

GB - 19SERVICE POSITIONPut unit into service position for easy access to underneath the deck.1. Place unit on a flat, level surface.2. Disconnect spar

2Ariens Company655 West Ryan StreetP.O. Box 157Brillion, Wisconsin 54110-0157 USATelephone (920) 756-2141Facsimile (920) 756-2407EC DECLARATION OF CON

GB - 20DRIVE BELT REPLACEMENT (self-propelled models)To remove drive belt:1. Disconnect spark plug wire.2. Set the right rear wheel to its lowest cutt

GB - 215. Tighten upper cable nut until bracket is secure between cable nuts.6. Engage engine/blade control. Measure distance between middle of z-bend

GB - 222. Check the adjustment and readjust as needed.NOTE: If the gap between the friction disc and aluminum drive plate cannot be adjusted to this t

GB - 23IMPORTANT: NEVER spray unit with high-pressure water or store unit outdoors. Store mower in a cool, dry, protected location.CleaningClean unit

GB - 24Wheel drive does not engage (Self-Propelled models)1. Wheel drive control not engaged.2. Drive belt out of position.3. Drive belt worn or damag

GB - 25SPECIFICATIONSModel Number 911330 911333 911334 911335 911396Description LM21SW LM21S LM21SW LM21S LM21SWLength - in. (cm) 61.5 (156)Height - i

Ariens Company655 West Ryan StreetP.O. Box 157Brillion, WI 54110-0157920-756-2141Fax 920-756-2407www.ariens.com

3CE Sound and Vibration – Bruits et vibrations CE – CE Geräusch- und Vibrationswerte – CE Geluid en trilling – CE støj og vibration – Livello sonoro e

GB - 4Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Assembly . . . . . . . . . . . . . . . . . . . . . . . 10Controls and Features .

GB - 5UNAUTHORIZED REPLACEMENT PARTSUse only Ariens replacement parts. Replacing any part on this vehicle with anything other than an Ariens authorize

GB - 6NOTATIONSNOTE: General reference information for proper operation and maintenance practices.IMPORTANT: Specific procedures or information requi

GB - 7Learn applicable rules and laws in your area, including those that may restrict the age of the operator.Read, understand and follow all safety p

GB - 8If you strike an object, or if equipment vibrates abnormally, stop engine at once, wait for moving parts to stop and disconnect wire from spark

GB - 9Poisonous battery fluid contains sulfuric acid. Contact with skin, eyes or clothing can cause severe chemical burns.ALWAYS wear safety glasses a