Owner/Operator ManualManuel Du Propriétaire/UtilisateurModels921025 – Power Brush 28(Serial No. 35000 and up)Power Brush 2804373900 9/11Printed in USA
GB - 101. Traction Drive Clutch Lever2. Speed Selector Lever3. Attachment Clutch Lever4. Recoil Starter Handle5. Brush Angle Remote Trigger6. Oil Fill
GB - 11STANDARD CONTROLS See Figure 4 on page 10 for all Controls and Features locations.Dual Handle Interlock When Attachment Clutch and then Tractio
GB - 12Fuel Shut-Off ValveIMPORTANT: The fuel shut-off valve MUST be in the closed position prior to transporting the unit.The fuel shut-off valve has
GB - 13Install spacers on the wheel spindle above or below the wheel support as shown. Turn the spacers so the slot in the spacer does not align with
GB - 14Fuel StabilizerGasoline left in the fuel system for extended periods without a stabilizer will deteriorate, resulting in gum deposits in the sy
GB - 153. Make sure that the traction clutch and attachment drive clutch levers are fully disengaged.4. Open fuel shutoff valve.5. Set the engine shut
GB - 16Fuel SystemGasoline left in the fuel system for extended periods without a stabilizer will deteriorate, resulting in gum deposits in the system
GB - 176. Remove attachment drive belt from engine sheave (it may be necessary to turn engine sheave using recoil starter handle).7. Support unit fram
GB - 18CHECK CLUTCH OPERATIONBrush must stop quickly when attachment clutch lever is released.Wheels must stop quickly when traction drive clutch leve
GB - 19Casters1. Grease fittings on left and right side caster shafts.DriveIMPORTANT: Wipe each lube fitting clean before and after lubrication. DO NO
GB - 2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Assembly . . . . . . . . . . . . . . . . . . . . . . . . 8Controls & Featur
GB - 20Figure 12OilGreaseOS7245
GB - 21RECOIL GUARD FOAM COVER INSTALLATION(Figure 13)The recoil foam cover slides over the starter handle and attaches to the recoil guard with Velcr
GB - 22ATTACHMENT DRIVE BELT REPLACEMENTRemove Attachment Drive Belt (Figures 15 and 16)1. Shut off engine, disconnect spark plug wire and allow unit
GB - 23TRACTION DRIVE BELT REPLACEMENT(Figure 16 and 17)NOTE: Brush assembly and frame must be separated and attachment drive belt removed from engine
GB - 242. Pull idler away from traction drive belt and remove belt from idler, crankshaft pulley and driven pulley (it may be necessary to turn cranks
GB - 25Check Attachment Idler Arm Roller Clearance(Figure 22)1. Remove the bottom cover.2. With the attachment clutch lever engaged, check the clearan
GB - 26Check Belt Finger Clearance(Figure 24)1. With attachment clutch lever engaged, the belt finger located opposite the belt idler must be less tha
GB - 2713. Insert new friction disc assembly into frame. Install washers onto carrier bearing and slide into speed selector arm. 14. Slide hex shaft t
GB - 28TROUBLESHOOTINGPROBLEM PROBABLE CAUSE CORRECTION Engine will not crank/start.1. Fuel tank is empty.2. Fuel shut-off valve closed.3. Engine shut
GB - 29To obtain a complete parts manual, find your model and serial number. Then go to www.ariens.com.SPECIFICATIONSModel Number 921025Engine SubaruE
GB - 3• Record Unit Model and Serial number here.• Record Engine Model and Serial number here.PRODUCT REGISTRATIONThe Ariens dealer must register the
Sno-Chore_2011.B30Sno-Thro®, Sno-Tek® and Chore Performing Equipment Limited WarrantyAriens Company (Ariens) warrants to the original purchaser that A
Sno-Chore_2011.B31Exceptions and LimitationsThe chart below details special exceptions to this warranty:Customer ResponsibilitiesRegister the product
Sno-Chore_2011.B32Exclusions - Items Not Covered by This Warranty• Parts that are not genuine Ariens, Gravely, Parker or Countax service parts are not
CARB_EPA_201133 CALIFORNIA AND EPA (UNITED STATES ENVIRONMENTAL PROTECTION AGENCY) EVAPORATIVE EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS
CARB_EPA_201134(4.) Repair or replacement of any warranted part under the warranty provisions of this article must be performed at no charge to the ow
Ariens Company655 West Ryan StreetBrillion, WI 54110-1072920-756-4688www.ariens.com
GB - 4SAFETY ALERTSLook for these symbols to point out important safety precautions. They mean:Attention! Personal Safety Is Involved!Become Alert!
GB - 5 1. WARNING! 2. CAUTION! 3. DANGER! 4. DANGER! 5. HOT SURFACES!EMISSION CONTROL SYSTEMThis equipment and/or its engine may include exhaust and e
GB - 6ALWAYS check overhead and side clearances carefully before operation. ALWAYS be aware of traffic when operating along streets or curbs.Keep chil
GB - 7Run unit a few minutes after clearing snow to prevent freeze-up of attachment.Disengage attachment when not in use.Disengage all clutches before
GB - 8Tools Required:•Tire Gauge• Pliers• 1/2-In. 3/8-In, 7/16-In, and 9/16-In Wrench or Adjustable WrenchUnpacking UnitUnfold Handlebar(Figure 3)1. R
GB - 9Check Tire PressureCheck tire pressure and adjust to the pressure listed on tire sidewall.Check Engine Crankcase OilIMPORTANT: Engine is shipped
Comments to this Manuals