Ariens Platinum 30 Specifications download pdf (Page 6)

EN - 6

EMISSION CONTROL SYSTEM

This equipment and/or its engine may include

exhaust and evaporative emissions control

system components required to meet U.S.

Environmental Protection Agency (EPA)

and/or California Air Resources Board

(CARB) regulations. Tampering with

emission controls and components by

unauthorized personnel may result in severe

fines or penalties. Emission controls and

components can only be adjusted by an

Ariens Company dealer or an authorized

engine manufacturer's service center.

Contact your Ariens Company Equipment

Retailer concerning emission controls and

component questions.

SAFETY RULES

Read, understand, and follow all safety

practices in Owner/Operator Manual before

beginning assembly or operating. Failure to

follow instructions could result in personal

injury and/or damage to unit.

ALWAYS remove key and/or wire from spark

plug before assembly, maintenance or service.

Unintentional engine start up can cause death

or serious injury.

Complete a walk around inspection of unit and

work area to understand:

• Work area • Your unit • All safety decals

ALWAYS check overhead and side clearances

carefully before operation. ALWAYS be aware

of traffic when operating along streets or curbs.

Keep children and people away. Keep children

out of work area and under watchful care of a

responsible adult.

NEVER allow children to operate or play on or

near unit. Be alert and shut off unit if children

enter area.

DO NOT allow adults to operate unit without

proper training. Only trained adults may

operate unit. Training includes actual

operation.

Keep area of operation clear of all toys, pets,

and debris. Thrown objects can cause injury.

Check for weak spots on docks, ramps or

floors. Avoid uneven work areas and rough

terrain. Stay alert for hidden hazards.

DO NOT operate near drop-offs, ditches, or

embankments. Unit can suddenly turn over if a

wheel is over the edge of a cliff or ditch, or if an

edge caves in.

Falling snow, fog, etc. can reduce vision and

cause an accident. Operate unit only when

there is good visibility and light.

NEVER operate unit after or during the use of

medication, drugs or alcohol. Safe operation

requires your complete and unimpaired

attention at all times.

NEVER allow anyone to operate this unit when

their alertness or coordination is impaired.

DO NOT operate unit without wearing

adequate winter outer garments. Wear

adequate safety gear, including safety glasses

with side shields, and protective gloves. Wear

proper footwear to improve footing on slippery

surfaces.

DO NOT wear loose clothing or jewelry and tie

back hair that may get caught in rotating parts.

Protect eyes, face and head from objects that

may be thrown from unit. Wear appropriate

hearing protection.

Avoid sharp edges. Sharp edges can cut.

Moving parts can cut off fingers or a hand.

ALWAYS keep hands and feet away from all

rotating parts during operation. Rotating parts

can cut off body parts.

NEVER place your hands or any part of your

body or clothing inside or near any moving part

while unit is running.

ALWAYS keep hands away from all pinch

points.

DO NOT touch unit parts which might be hot

from operation. Allow parts to cool before

attempting to maintain, adjust or service.

Never direct discharge towards persons or

property that may be injured or damaged by

thrown objects. Use extreme caution on gravel

surfaces. Stay alert for hidden hazards or

traffic. Adjust Skid Shoes so Scraper Blade

does not contact gravel.

DO NOT throw snow any higher than

necessary.

Deflected materials can cause injury and

property damage.

Always stand clear of the discharge area when

operating this unit.

Fumes from engine exhaust can cause injury

or death. DO NOT run engine in an enclosed

area. Always provide good ventilation.

ALWAYS disengage attachment, stop unit and

engine, remove key and allow moving parts to

stop before leaving operator’s position.

ROTATING AUGER CAN CAUSE SERIOUS

INJURY. NEVER ATTEMPT TO UNCLOG OR

CLEAN UNIT WHILE ENGINE IS RUNNING.

Read, understand, and follow all instructions in

the manual and on the machine before starting.

Understand:

• How to operate all controls.

• The functions of all controls.

• How to STOP in an emergency.

Before starting engine, disengage control(s).

Use only approved extension cords and

receptacles when starting units equipped with

electric starter. DO NOT connect electric

starter cord to any wiring system that is not a

three-wire grounded system.

ALWAYS allow unit and engine to adjust to

outdoor temperatures before clearing snow.

DO NOT overload the machine capacity by

attempting to operate or to clear snow at too

fast a rate.

Slow down and turn corners slowly.

Do not operate in reverse unless absolutely

necessary. ALWAYS back up slowly. Always

look down and behind before and while

backing.

Disengage attachment drive when traveling

from one work area to another.

1 2 3 4 5 6 7 8 9 10 11 ... 41 42

Comments to this Manuals

No comments

Ariens Platinum 30 Specifications Page 6

Comments to this Manuals

Related products and manuals for Garden tools Ariens Platinum 30