Ariens SNO-THRO 932041 - ST7524E 9 User Manual download pdf (Page 15)

GB - 15

5. Set throttle to proper starting position.

6. Insert key into ignition switch and push into RUN

position. DO NOT twist key after it is inserted.

7. Grasp starter handle and pull rope out slowly until

it pulls harder. Let rope rewind slowly.

8. Pull rope with a rapid continuous full arm stroke.

Let rope rewind slowly.

IMPORTANT: DO NOT let Starter Handle snap against

Starter.

9. Repeat steps 7 and 8 until engine starts. (If

engine does not start, refer to

TROUBLESHOOTING on page 25.)

10. Adjust choke as needed.

11. Set throttle to Part Throttle or Slow position for

adaptation to outside temperature or travel. Set

throttle to Fast position for normal operation.

Electric Start (120V)

1. Connect extension cord to starter.

IMPORTANT: Prevent damage to unit. Know voltage of

your starter and only use matching outlets.

2. Plug extension into 120V 3-wire, grounded outlet.

3. Turn discharge chute straight ahead.

4. Make sure that the traction clutch and attachment

drive clutch levers are fully disengaged.

5. Push Primer Bulb 2 or 3 times for cold engine.

NOTE: When temperature is below -15° F (-26° C)

additional priming may be needed.

6. Insert key into ignition switch on engine and push

into "Run" position. DO NOT twist key after it is

inserted.

7. If engine is cold, apply choke. A warm engine

requires less choking than a cold engine. See

Engine Manual for detailed instructions.

8. Set throttle to proper starting position.

9. Press starter button on engine until engine starts.

IMPORTANT: DO NOT operate starter more than 15

seconds per minute, as overheating and damage can

occur. (If engine does not start, refer to

TROUBLESHOOTING on page 25.)

10. Adjust choke as needed.

11. Disconnect power cord from outlet, then starter.

12. Set throttle to Part Throttle or Slow position for

travel or adaptation to outside temperature. Set

throttle to Fast position for normal operation.

Shut Off

1. Release Traction Drive Clutch Lever and allow

unit to come to a complete stop.

2. Run Impeller a few minutes after use to prevent

freeze-up of Impeller.

3. Release Attachment Clutch Lever and wait for all

moving parts to come to a complete stop.

4. Move Throttle to the “Stop” position.

5. Remove key.

SNOW REMOVAL

IMPORTANT: Allow unit and engine to adjust to the

outdoor temperature before clearing snow.

NOTE: Attachment clutch should be engaged before

wheel drive clutch when throwing snow.

1. Select Speed Control position and direction.

2. Engage Attachment Clutch - Right Hand Lever.

3. Engage Traction Drive Clutch - Left Hand Lever.

IMPORTANT: DO NOT overload unit capacity by

attempting to clear snow at too fast a rate. Use slow

speed to clear deep or hard packed snow.

Tips for Operation

Snow is best removed as soon as possible after snow

fall.

To clear an area, run unit in an overlapping series of

paths. For large areas, start in the middle and throw

snow to each side, so snow is not cleared more than

once.

ALWAYS direct snow away from area to be cleared and

with direction of the wind.

TRAVELING

To travel from one work area to another:

1. Set Throttle to Slow or Part-Throttle position.

2. Press down on handlebars enough to raise front

of unit slightly off surface.

3. Engage wheel drive clutch without engaging

attachment drive clutch.

TRANSPORT

ALWAYS shut off engine, remove key, and close fuel

shut-off valve when transporting unit on a truck or

trailer.

Use extra care when loading or unloading unit onto

trailer or truck.

Secure unit chassis to transport vehicle. NEVER

secure from rods or linkages that could be damaged.

DO NOT transport machine while engine is running.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 29 30

Comments to this Manuals

No comments

Ariens SNO-THRO 932041 - ST7524E 9 User Manual Page 15

Comments to this Manuals

Related products and manuals for Cars Ariens SNO-THRO 932041 - ST7524E 9