Owner/Operator Manual Models924124 – ST926DLE924125 – ST11528LE924126 – ST11526DLE924127 – ST11528DLE924128 – ST1332LE924335 – ST926DLE924336 – ST1152
GB - 10Install Discharge Chute (924124-128, 335-338, 516)Figure 5.1. Grease underside of discharge chute ring (if not already greased).2. Remove mount
GB - 112. Turn the chute gear until the solid pin is towards the rear of the unit and a threaded stud aligns with the chute motor (Figure 7).3. Remove
GB - 12Connect Battery (924516, 517)1. Remove wing nuts from battery cover.2. Install wire lead to battery terminal.3. Install battery cover and tight
GB - 131. Traction Drive Clutch Lever2. Oil Fill/Dipstick3. Muffler Guard4. Belt Cover5. Discharge Chute Deflector6. Discharge Chute7. Electric Chute
GB - 14CONTROLS AND FEATURESSee Figure 11 for all Controls and Features locations.Dual Handle Interlock When Attachment Clutch and then Traction Drive
GB - 15Choke Control Knob1. Choke Closed position: chokes off air to engine for easier start.2. Choke Open position: allows for normal operation.IMPOR
GB - 16Differential Lock (924124, 126, 127, 335, 336, 337, 516, 517)Differential Lock knob is located on the Left Wheel Hub. With differential locked
GB - 17FILLING FUEL TANKFuel Shut-Off ValveIMPORTANT: The fuel shut-off valve MUST be in the closed position prior to transporting the unit.The fuel s
GB - 18NOTE: When temperature is below -15° F (-26° C) additional priming may be needed.4. If engine is cold, apply choke. See Engine Manual for detai
GB - 191. Select Speed Control position and direction.2. Engage Attachment Clutch - Right Hand Lever.3. Engage Traction Drive Clutch - Left Hand Lever
2Ariens Company655 West Ryan StreetP.O. Box 157Brillion, Wisconsin 54110-0157 USATelephone (920) 756-2141Facsimile(920) 756-2407EC DECLARATION OF CONF
GB - 20CHECK DUAL HANDLE INTERLOCK Without the engine running, press down (engage) both clutch levers. Release attachment clutch lever. Attachment clu
GB - 21CLEAN BATTERY (924516, 517)IMPORTANT: Battery is maintenance free. Do not tamper with or attempt to open battery. See Service and Adjustments f
GB - 22DISCHARGE CHUTEIf chute does not stay in position while operating, tighten nut on carriage bolt at pivot point to increase tension on spring (F
GB - 23SCRAPER BLADEIMPORTANT: Damage to auger/impeller housing will result if blade wears down too far.Scraper blade is adjustable to compensate for
GB - 24ATTACHMENT CLUTCH/BRAKE ADJUSTMENT(Figures 21 and 22)1. Remove belt cover. 2. Check belt alignment (Figure 24).Engine sheave and attachment pul
GB - 25TRACTION DRIVE CLUTCH ADJUSTMENTIf drive slips, adjust traction clutch to compensate for friction disc wear.To adjust traction clutch: 1. Place
GB - 268. Remove attachment drive belt from attachment pulley (hold brake away from belt).Install new attachment drive belt:1. Place new attachment be
GB - 275. Release traction clutch lever, shift to third (3) position, and remove friction disc.6. Secure new friction disc on hub with five cap screws
GB - 28* Available in CE countries. TROUBLESHOOTINGPROBLEM PROBABLE CAUSE CORRECTION Engine will not crank/start.1. Fuel tank is empty.2. Fuel shut-of
GB - 29 SPECIFICATIONSModel Number 924124 924125 924126 924127 924128DescriptionST926DLE ST11528LE ST11526DLE ST11528DLE ST1332LEEngine - TecumsehOH31
3CE Sound and Vibration – Niveau sonore et vibration CE – CE-Geräuschpegel und Vibrationswerte – Livello sonoro e vibrazioni CE – Sonido y vibración C
GB - 30 SPECIFICATIONSModel Number 924335 924336 924337 924338 924516 924517DescriptionST926DLE ST11526DLE ST11528DLE ST1332LE ST1332DLE ST1336DLEEngi
GB - 313-Year Limited Sno-Thro WarrantyAriens Company warrants to the original purchaser that consumer products manufacturedby Ariens Company will be
Ariens Company655 West Ryan StreetP.O. Box 157Brillion, WI 54110-0157920-756-2141Fax 920-756-2407www.ariens.com
GB - 4Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . 9Controls
GB - 5DELIVERYCustomer Note: If you have purchased this product without complete assembly and instruction by your retailer, it is your responsibility
GB - 6SAFETY DECALS AND LOCATIONSALWAYS replace missing or damaged Safety Decals. Refer to figure below for Safety Decal locations.1. DANGER!2. WARNIN
GB - 7Keep area of operation clear of all toys, pets, and debris. Thrown objects can cause injury. Check for weak spots on docks, ramps or floors. Avo
GB - 8Before cleaning, removing clogs or making any inspections, repairs, etc.: disengage clutch(es), stop unit and engine, remove key, allow moving p
GB - 9• In case of internal contact, DO NOT induce vomiting!Before tipping unit up onto housing, remove fuel so no spills will occur and remove batter
Comments to this Manuals