Owner/Operator & Parts ManualModel891003 – HD Series Three-Bag BaggerHD Series Bagger03776000B 5/10Printed in USA
10INSTALL COUNTERWEIGHTS1. Insert two 1/2-13 x 7 round head square neck bolts (item 2) in the cz-hd counterweight bracket (item 20) and then install t
117. Connect the lower heat deflector to the bagger mount weldment (item 4) with the hardware removed in step 2. See Figure 7.8. Install the heat defl
12INSTALL BAG ON FRAME (FIGURE 9)1. Thread the zoom bag frames (item 16) through the sleeve on the open end of the mesh xl bagger bags (item 15).2. In
13INSTALL BAGSInstall Bags on Catcher Frame1. Install the mesh xl bagger bags (item 15) on bagger cover assembly (item 9) with the heat resistant side
145. Install the two coupling nuts to deck with two 0.31-18 x .75 round head square neck bolts with Loctite patch as shown in Figure 13.6. Install the
15Removing Bagger Kit1. Lift thumb latch and remove hose from blower assembly and bagger assembly (see figure 14 on page 14).2. Remove belt guard.3. R
16Before Each Use1. Check bagger parts for wear, deterioration or damage. Replace ONLY with original manufacturer service parts before operating.2. Ma
17Ariens and Gravely Dealers will provide any service or adjustments that may be required to keep your unit operating at peak efficiency.Maintenance S
18IMPORTANT: NEVER spray unit with high-pressure water. DO NOT store unit outdoors.NOTE: If needed, the cloth bags can be washed with low pressure wat
19SAFETY DECALSItem Part No. Qty. Description1 05359700 1 Bagger Cover Decal2 07731400 1 Mower Pan Danger Decal3 07742300 1 Warning Decal4 08088200 1
2Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20BLOWER ASSEMBLY TO MOWER DECKOAe005234567891011121415161217211331918
21BLOWER ASSEMBLY TO MOWER DECK (CONT.)Item Part No. Qty. Description1 00166000 1 Housing, Blower2 06439300 2 Washer, Flat Steel .38 x 1.50 x .062 3 0
22BLOWER ASSEMBLYOEe006138867130106111213109212141617188181115109210 193520214222325262723282630293432312424335
23BLOWER ASSEMBLY (CONT.)Item Part No. Qty. Description1 00166000 1 Housing, Blower2 05900008 2 Bolt, Hex .25-20 x .503 00169951 1 Plate, Skid4 065435
24MOUNTING ASSEMBLY64121826251173109112
25MOUNTING ASSEMBLY (CONT.)Item Part No. Qty. Description1 03735551 1 Weldment, Bagger Head Mount2 05948700 6 Bolt, Hex .38-16 x 1.00 Grade 53 0654550
26BAGGER COVER ASSEMBLY1112131852313163023952021251235678119101714153244262227282812293
27BAGGER COVER ASSEMBLY (CONT.)Item Part No. Qty. Description1 06802500 11 Rivet, Pop .187 x .4022 00165800 1 Cover, Bagger with Decal3 03803800 40
28COUNTERWEIGHT ASSEMBLYItem Part No. Qty. Description1 03400051 1 Counterweight Bracket2 07415400 2 Screw, .38-16 x .75 Self-Tapping3 06224100 2 Bolt
ARIENS COMPANYGRAVELY® | STENS® | LOCKE® | NATIONAL® | BYNORM® | EVERRIDE® | GREAT DANE® Com_Lawn_201029 of 31Two-Year Limited Lawn and Garden Commerc
33. Review control functions and operation of the unit. Do not operate the unit unless all controls function as described in this manual.4. Review rec
ARIENS COMPANYGRAVELY® | STENS® | LOCKE® | NATIONAL® | BYNORM® | EVERRIDE® | GREAT DANE® Com_Lawn_201030 of 31To obtain warranty service, the original
ARIENS COMPANYGRAVELY® | STENS® | LOCKE® | NATIONAL® | BYNORM® | EVERRIDE® | GREAT DANE® Com_Lawn_201031 of 31
Ariens CompanyGRAVELY655 West Ryan StreetBrillion, WI 54110-1072920-756-2141Fax 920-756-2407www.ariens.com or www.gravely.com
42. DANGER ROTATING PARTS Always keep feet and hands away from rotating parts.Never direct discharge towards persons or property that may be injured o
5ALWAYS check overhead and side clearances carefully before operation. ALWAYS be aware of traffic when operating along streets or curbs.Keep children
6Stop and inspect equipment if you strike an object or if there is an unusual vibration. Repair, if necessary, before restarting. Never make adjustmen
7ALWAYS block wheels and know all jack stands are strong and secure and will hold weight of unit during maintenance.Release pressure slowly from compo
8NOTE: The complete blower assembly installs with a combination of parts provided in a separate blower mount kit and in this bagger kit and with parts
9ODD0182 Figure 3202345689191471011212413151617181222312
Comments to this Manuals